Uniden BC796D Base Scanner - Answered Questions & Fixed issues

check uniden web site should find info. JR

Contact "Scanner Master" in the Dayton Ohio area.

• Hi, I can help.

• This happens a lot to people just setting up a scanner like this. Try these suggestions, I think you'll be up and running in no time.

• You have to make sure the BAUD rate is set and make sure your PC control is turned on in your scanner. A BAUD is the rate per second data is sent.. A BAUD rate of 38400 (or what ever BAUD the software is at). I think parts 3,4 and 5 in the your scanner menu cover this. If you have the FIFO buffer set then remove it from your settings > control panel > comm ports. You will get the best results if you have that software read the bank before writing to it. Relabel your comm port settings if you need to as well ie. port 1, port 2 etc.

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa,

Regards, Tony

because all of your banks are locked out....

Just program a p-25 apco into a regular channel of your scanner... in your conventional scan mode...Just go to a certin channel of your scanner and program it in and it will automatically come in the APCO -P25...I have one of these scanners....ITs a wicked scanner...a good one...

it could be that your telescopic antenna that you got with your scanner could be Bad try putting another antenna on it. or try an outside base scanner antenna....

For a comprehensive database of active frequencies in your area (they're not codes), and a lot of other useful scanning information, visit:
www.RadioReference.com

Bill B.
Listening in since the 60's

www.uniden.com/pdf/BC796Dom.pdf -
Above is your manual and below is your support site, use these to do as you want, it is all explained in the manual, if you get stuck, contact them direct.
http://www.uniden.com/products/productdetail.cfm?product=BC796D

Setting DELAY for All Search Ranges
You can set the scanner to have a delay after the end of a transmission before searching
resumes. This slows searching, but helps you prevent missing replies on a frequency.
1:SERVICE OPTION → :CHAIN SEARCH → 3:DELAY
1:NONE
The delay is turned off.
2:1 SECOND
The delay time is 1 second.
3:2 SECONDS
The delay time is 2 seconds.
4:4 SECONDS
The delay time is 4 seconds.
28
5:INFINITE
When the scanner stops on a transmission, you must press RSM to resume
searching.
6: -2 SECONDS
The scanner only stops on transmissions for 2 seconds, then automatically
resumes. To hold on the transmission, press /HOLD during the 2-second pause.
7: -5 SECONDS
The scanner only stops on transmissions for 5 seconds, then automatically
resumes. To hold on the transmission, press /HOLD during the 5-second pause.
8: -10 SECONDS
The scanner only stops on transmissions for 10 seconds, then automatically
resumes. To hold on the transmission, press /HOLD during the 10-second pause.

For a comprehensive database of active frequencies and systems in your area, visit:

www.RadioReference.com

Bill B

Try tuning known frequencies, such as the NOAA weather channels, to verify the working condition of your scanner. If it picks them up, you don't have your local police system/frequencies programmed properly. If there's no reception, even on NOAA, you have an antenna or receiver problem that may need professional attention.

In case you need it, you can download/print the manual for your scanner here:

http://www.uniden.com/pdf/BC350Com.pdf

For a comprehensive database of active frequencies in your area, visit:

www.RadioReference.com


Bill B

You can download a manual for this unit at, BC796DOM.pdf it is 84 pages....hope this was helpful...

Thats as long as it will delay... hope this helps..

how do you know its sensitivity is 25 microvolts? have you checked the antenna connections to make sure they are clean and tight? If there is no problem with the antenna/lead in section,i would check the power supply voltage to see if its right and then the first rf amp, which is probably an field effect transistor near the antenna,they are often damaged by static charges.

hello there
please try these links they have worked for me

1. Scanner Frequencies & Codes Free Trunked Fleet ID's for your area (Works with Scancat) Military Base Operations Frequencies ... Get a scanner frequency list by email for your county, ...www.bearcat1.com/free.htm - Cached
2. Portland Police Scanner | Portland, Oregon Crime & Emergency Dispatcher ... ... use of a Trunk Tracking Scanner and entering the Talkgroup codes listed in the next section. ... your Business Listing for free. Obits / Death Notices ...oregonlive.com/policescanner/...?/policescanner/police_codes.frame - 64k - Cached
3. Scanner Feeds ... Feeds Police Codes Police 11 Codes General Codes General Acronyms ... They are free. ... Big Bear, California Police Scanner (web-based) Los Angeles Police ...members.shaw.ca/crazykid755/scanner - Cached

The Owner Manual is here Noel

Bearcat BC-890XLT Scanner owner's Manual

repeater-builder.com https://www.repeater-builder.com > uniden > pdf PDF Please read this Operating Guide thoroughly before operating the scanner. Optional Accessories. The following optional accessories for your BC 890XLT are ... 40 pages ..

Some help here, but what you want to be likely not possible. https://www.google.com/search?q=Uniden+Bearcat+BC+220XLT+service+manual ..

All questions need full 'make model (what it is)' or we guess. I see a number of UBC3000.

Uniden - UBC3000XLT Battery

Complete Battery Source https://www.completebatterysource.com > uniden-ubc... The Uniden - UBC3000XLT Nickel Metal Hydride (NIMH) battery is the perfect replacement battery at a great price! The Uniden - UBC3000XLT battery is ... Capacity: 1100 Length inches: 2.7 US$43.55

Here is the wiring diagram for connecting a D104-M6B microphone to a Uniden 880 radio:

• Shield: Connect to pin 1 of the microphone jack on the radio
• White: Connect to pin 2 of the microphone jack on the radio
• Red: Connect to pin 3 of the microphone jack on the radio
• Black: Connect to pin 4 of the microphone jack on the radio

It's important to note that not all Uniden 880 radios are wired the same way. If you're unsure about the wiring on your specific radio, it's best to consult the manual or contact Uniden customer support for assistance.

Question edited for clarity and add maker + (what it is). Question moved from Misc. You will have to contact Uniden direct. This search query should find it. The CLT model seems better known https://www.google.com/search?q=UBC370XLT+schematic More here including software https://www.google.com/search?q=%22UBC370XLT%22 ..