Top 20
Emerson EWF2704 TV Questions & Answers
Att remote code for emerson EWF 2704
Almost impossible, Emerson uses odd codes and for that reason charges a lot for a new remote, if you can even find a new one.Cable provider remotes have less than sixty average codes built into them so I doubt that remote will work on that emerson.
How to do a reset on my emerson lc30em1 t.v.
Visit this site. It has all the details about how to enter the service mdoe and select rest options to many models of TVselectronicshelponline(.)blogspot(.)comin name "Electro-Help"Type this address on the search box of your browser, without brackets, and press enter.
Can't get it on A/V channel without remote.
The Emerson TV requires the original remote to enable the A/V section and other area's of the set. Universal Remotes will not give access to the area you need. The only option is buy the original or track down a tv repair shop in the off chance he or she may have a second hand one.
I have an Emerson
hi. There is no way to change the input without a remote. go to this link to purchase an emerson replacement remote. You will be so glad you did http://www.replacementremotes.com/EMERSON/Replacement-Remotes-New-OEM-TV-DVD-Remote-Controls-page-1.html
Joe
Thanks for choosing Fixya!
TV turns on and a
Hello
There is total vertical swee failure occured on your TV. All CRT based telivisions have both vertical and horizontal sweep to display picture on the screen. In your TV, vertcal sweep has gone out; and horizontal sweep is there, that is why you see a bright horizontal line on the screen.
There are mainly two reasons for this fault. One is bad soldering at the legs of the vertical output Ic, and the other is Vertical Output Ic failure.
You just open your tv, and locate the vertical output Ic. It can be located by following the wires that goes from the deflection Yoke of the picture tube to main board. This will contain four wires, out of which two of them will be thick, usuall red and blue, and the other two will be thin relative to the above said pair, may be green and black, or green and yellow. You just follow the two thin wires, as they are carrying vertical sweep signal to the deflection yoke.
Normally these four wires are socket pin type arrangements, which has pluged into the printed circuit board, and can be detached by pulling its plug from the board. Just make the board upside down and carefully look for any loose contacted solder joints of any other to the solderings of this plug. If it is found ok, then follow the print to where it goes to. it will lead you to vertical output Ic said above. It will be screwed onto a metal plate, to radiate heat out of it when it works. Just look for any loose solderings there on the legs of the Ic. It is quite normal that these solderings will get loose with time, as these ponts are heated and cooled several times.
Resolder all these legs with applying a little more solder, without any short between these legs. Switch on the TV all connections have given. Normally this will retify your problem. If not, IC stated above is faulty. Resolder it out from the board and go for a same type and number. Replacing it will rectify your complaint. OK.
There is a black block in front of the screen
Hi alice,
Welcome to FixYa.
My name is John. I will be assisting you with your issue.
You may have hit the Closed Caption (CC) on the remote by accident,or TEXT.
Scroll down the menu and find it, and disable it.
Thanks for choosing FixYa.
John
Need a power cord for
RADIO SHACK, BEST BUY, or CHEAP.com these are your most common places to find power cords. oh oh also Wal-Mart.
Cannot find code for this tv
Hello
Emerson TV has a lot of codes to check. I'm not sure about which code will activate your TV. Anyway I'm sending all of them to you. Proceedings are also given. Switch off the TV and switch it on before each code test. Not power off and on by remote control I mean. Switch it On and Off with its front panel power switch. Ok
{ 0004 0009 0044 0135 0049 0051 0189 0053 0147 0039 0130 0227 0233 0250 0252 0254 0257 0265 0266 0310 0325 0456 0040 0041 0042 0021 0023 0024 0179 0045 0025 0027 0030 0032 0034 0035 0037 }
Proceedings
- Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
- Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
- Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
- With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Emerson TV input option
Tries the channels + or - buttons a couples times on the tv manual controls buttons on the tv.U will get in the input option.This solution work for many tvs don't the input option on their universal remotes,without the original remotes.Ur tv don't know.
There is no picture.
hi,why did you want buy a picture tube?;did you break the tube by
some how,it will cost you a bundle more then buy a new tv...
for me i expect some electronic problem in the power supply or in the high voltage circuit or its may be just a fuse?!
regards alan .
It will not turn on,
That would be the common power supply aka high-voltage transformer failure problem. This is the component that attaches from power cord to main circuit board to provide power. These do commonly go out. They need to be tested with a voltmeter where the transformer/supply attaches to the board.
Not finding what you are looking for?