20 Most Recent
Philips Magnavox 27MS343S 27" TV - Page 7 Questions & Answers
2 Problems
1st problem-reduce the supply voltage on the power supply to the recommended 95v.if prob does not clear change suspect capacitors around the line output transformer.
2nd problem-check;continuity of av-cables
;dry joints on av inlet sockets of the tv card.
No sound
hi first of all u should check ur transistor connections.Check your
Horizontal and vertical output transistors.You should also
check the horizontal and vertical yoke connections as well as your low
voltage regulators.... if any of these got damaged u should purchase a
new one.. but try to purchase with the help of a tv service assistant...
thank u!!!
rate me
How do u turn the tv when it's in child lock?
Just had the same problem and used a cheap $4 universal remote with Magnavox code "0224" and it turned on! Hope this helps guys!Put code in twice if it doesn't work the first time.Another one said code 0711. if first one does not work.
Magnavox 27MS343S 27" TV
You will for sure need to borrow a remote from someone to do this. But I will give you the way to unlockit just in case you can get one. Philips sets use a four digit code to control the v-chip. The override code for Philip sets is 0711, although it may say "Incorrect code" the first time to trick you. If "Incorrect code" is displayed, simply enter 0711 again. To use it hit the MENU key to get to the menus. Go up or down until you reach AUTOLOCK or SMARTLOCK, depending on the model, and push the "right arrow" key on the remote. Enter the override code, and enter it a second time if it says it is incorrect.
Once in the AUTOLOCK or SMARTLOCK menu, go to BLOCK, and push the "right arrow" key. Go to BLOCKING OPTIONS and press the "right arrow" key. Go to MASTER DISABLE and press the "right arrow" key so that it says "MASTER DISABLE ON". The v-chip is now reset. Good Luck
My tv has a sound and no picture
Its horizontal output section circuit should be troubleshooted. Contact any experienced service technician. If
you are not familiar with electronics, do not attempt to repair. Whether you suffer fatal electrical shock!
Instead, contact the nearest service center.
I need code for smartlock
Philips sets use a four digit code to control the v-chip. The override code for Philip sets is 0711, although it may say "Incorrect code" the first time to trick you. If "Incorrect code" is displayed, simply enter 0711 again. To use it hit the MENU key to get to the menus. Go up or down until you reach AUTOLOCK or SMARTLOCK, depending on the model, and push the "right arrow" key on the remote. Enter the override code, and enter it a second time if it says it is incorrect.Once in the AUTOLOCK or SMARTLOCK menu, go to BLOCK, and push the "right arrow" key. Go to BLOCKING OPTIONS and press the "right arrow" key. Go to MASTER DISABLE and press the "right arrow" key so that it says "MASTER DISABLE ON". The v-chip is now reset.If you wish to know more, check this link.
Magnavox 37MF231D/331D LCD
1. Remove all screws around perimeter, one screw at the lower right at (Side A/V), and 2 1”round plastic knob s.
2. Remove back cover
3. At lower left side remove 2 screws for On/Off switch cut tie wrap that holds wire down for free movement.
4. Disconnect wire connector to side A/V at lower right side
5. Disconnect wire connector to right side circuit Board
6. Disconnect wire connector to left side circuit board
7. Remove the 2 mounting brackets upper left and upper right 2 screws each.
8. Remove 3 screws each side of the metal box in the middle
9. Fold back metal tape off bottom and top of metal box
10. 1 wire connector at top of box I left connected
11. Flip metal box over towards top of Tv. Be careful of wire at top thats still connected.
12. On left side in box is power supply board
13. Towards bottom of board you should see the numbers C2081 and C2074
14. Remove the six screws holding down power supply board
15. Flip board down towards bottom of Tv.
16. Unsolder capacitors replace with new 1200uf 35v and 2200uf 35v 105°C radial capacitors
17. Capacitors should be around 1/2” to 5/8” dia. X 1.25 long appox. 2 Wires come out of one end should be .030 dia.
18. Reassemble in reverse order and enjoy
Tv making a buzzing noise
I would check the Flyback, and horizontal output transistor. Could also be a grounding issue. If you're not familiar with fixing them get it serviced.
Not finding what you are looking for?