E-Machines eMonster 500a PC Desktop - Answered Questions & Fixed issues
Bios reset emonster 500a emachine
start the computer and while its comming on ( or loading) press f1 or the delete key holdig it down for a few seconds this should get you into the bios. you can then reset the bios to default and then save changes and exit.
6/27/2012 1:49:16 PM •
E-Machines...
•
Answered
on Jun 27, 2012
•
118 views
When i piuged in their is no power what i have to
Check on the power supply and make sure the main power switch is turned on. If it is turned on make sure the plug works by pluggin in a lamp or other simple device that you know works. Also if it is on a power strip make sure you did not turn the strip off. If all these work and there is no power when you hit the front button you might have a bad power supply. If that is the case contack emachine and they offer a warranty repair.
4/7/2010 2:00:34 PM •
E-Machines...
•
Answered
on Apr 07, 2010
•
45 views
EMachines eMonster 500A Restore Disk
I suggest finding the specific drivers that he deleted. Typically, when a computer begins to get slow, either 1 of 3 problems occur. 1. The drivers are insufficiently up to date. 2. There's too much clutter on the hard disk, RAM, and CPU. Lastly, driver files and start up files get deleted. The best way to fix that slow problem is downloading the driver files.
2/5/2009 1:35:02 AM •
E-Machines...
•
Answered
on Feb 05, 2009
•
258 views
I was in the process
with cd in rom
restart hit F7 during restart
highlight boot from cd press enter
let me know if that helped
if not what message are you getting
1/23/2009 5:43:55 AM •
E-Machines...
•
Answered
on Jan 23, 2009
•
87 views
I have an eView 17f3 computer monitor that was
well that is 17,000 volts there 17kv and can be lethal .
CRT is cathode ray tube and 2nd anode is 17kv, 1kv per inch screen.. we use a chicken stick to discharge that.
one guy gut hit here and flew across the room ,hit head and next up paramedics deep.. not fun to see that. ive taking 600v but never again.
vaccum seal, why do that.???
send it to the , toxic lead recycle center, let them do the danger work
when I was only 16yo I worked in TV shop and I had do that "nnipp" that in the bud on all CRT sent off to refurb. (or toxic trash) (we sold them all here, you name it)
we had to remove the socket there find he glass bud there dead center and full PPE, and snap it with wire cutters and it sucks in air fast. later in military too on old radar scopes, i worked .
the vacuum inside is pure and prefect, zero gasses.
implosion hazard exists. a glass flies in the bounces out and hits you and then next up blind i one eye. leave CRT alone to the trained.
5/16/2022 5:02:25 PM •
E-Machines...
•
Answered
on May 16, 2022
•
62 views
Hi i have emachine 8230 tower
firstly lets think why a Working pc would no longer BOOT. The boot process then. a pc starts the bios which POST's. this results in ONE BEEP which might be followed by messages(if you get several beeps then they are like morse code long/short and count out an error code). when you get your ONE BEEP the pc is working. when it then HANGS(appears to do nothing) its usually because of either a) the cd drive is duff so disconnect its cables. b) the hard drive is duff so disconnect its cables c) the hard drive hasnt quite died yet but has some very slow sectors and is making the Clackety Clack of the heads recalibrating every few seconds. d) there could be a a gpu card bios glitch and your pc is running but you just have a blank screen. some hints then 1) never start removing parts as that corrupts the CMOS(the battery backed up configuration for your BIOS) so you may need to clear your cmos. 2) never play with the idea of changing ram sticks as people usually end up putting them in any old slot(which may result in a non working pc). make sure a PAIR is fitted in slots 0/2 and a separate matching pair in 1/3 slots not in slots 0/1 which is two half pairs. Other factors. 1) a short circuit. your PSU has built in protection, if the psu fan(inside case of the psu) turns and kicks back and immediately stops you have a short circuit and its cuts the power to avoid a fire/meltdown, which could be caused by high wattage gpu(>60 watts) without its extra power cables fitted or wrongly connected front usb cables or removing a mainboard and fitting it into a new box where the board has its support posts NOT lined up with the holes fro the screws so the post is touching underside of the board circuits. hope some of that helps.
11/22/2018 8:38:26 AM •
E-Machines...
•
Answered
on Nov 22, 2018
•
133 views
Emachines 3240 - cannot recover
Download a Linux distro to a flash drive or DVD and see how well it runs off that. There's HDD utilities like SuperGrubDisk that can diagnose things.
4/8/2017 2:22:18 PM •
E-Machines...
•
Answered
on Apr 08, 2017
•
221 views
E machines model et1831 will not boot up
try booting to safe mode. by using f8if that works, try a system restore to a previous date. if that does not help, then it must be a windows corruption and parallel install or repair install will be needed, it can also be fixed by manual troubleshooting and repairing the files.
7/30/2015 5:06:54 PM •
E-Machines...
•
Answered
on Jul 30, 2015
•
132 views
Not finding what you are looking for?