20 Most Recent Coleman Propane Forced Air Heater w/Electronic Ignition (50,000-80,000 BTU) - Page 4 Questions & Answers


first thing i would do is follow the short rubber tub from the draft switch to the furnace. pull the hose off the furnace body and run a paper clip, or such, into the hole. replace the hose and see if that helps. check the vent ing for blockage and then replace the switch

Coleman Propane... | Answered on Jan 19, 2012


how old is the unit? is this in a mobile home?

Coleman Propane... | Answered on Nov 22, 2011


This air switch proves that the inducer motor is running and moving air. If not, check to make sure that the inducer motor starts and that the flue is free of restrictions.....eg. bird nest, ice/snow, or some other critter that found a new home.

Coleman Propane... | Answered on Nov 20, 2011


Defective combustion air switch. The 3 blinks are an error code. You didn't say, but I'm guessing you have a Coleman Evcon. They had alot of defective Combustion air switches. Your specialists were not that.

Coleman Propane... | Answered on Nov 19, 2011


Hello, I would get another company to come out and check the Furnace. The gas valve starts and stops the flow of gas to the burners and if the gas pressure is not correct, it could be overfiring the burners. So yes they are related. but this is the fault of the service company and if they make mistakes by installing the wrong gas valve then I would look for a differant company.

Coleman Propane... | Answered on Nov 18, 2011


Long as that limit is open then you ain't gonna have no heat amigo. Check your smoke stack for air restrictions that might cause the limit to trip.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Coleman Propane... | Answered on Nov 09, 2011


Talk about a misnomer? Electric heat works way diff than gas heating. On electric heat multiple strips and a fan of course. But if they all come on at the same time then the breaker would trip so they use a sequencer for that job. Gas heat uses a bi-metal probe which twists around and turns the fan on when the temp reaches 110 in the plenum. Yall either have a bad fan or capacitor OR the thang that turns the fan on ain't doin it.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Coleman Propane... | Answered on Nov 06, 2011


Hello, the blower motor typically will not turn on if the capacitor is bad, control board is bad, or motor is shot. If there is voltage coming from the board to motor than that eliminates the board. If you can spin the blower wheel by hand and it starts up then the capacitor is bad and must be replaced. If you have power to motor and capcitor is good that only will leave the motor as being shot.

Coleman Propane... | Answered on Nov 04, 2011


Hello, Maybe this will help you some.

http://home.howstuffworks.com/how-to-repair-gas-furnaces.htm

I hope it does, Mike

Coleman Propane... | Answered on Oct 31, 2011


Check to see if you are getting power to the ignitor... if not then the ignition control module is bad or there is another control that is keeping the control module from trying to light the furnace...
Check for 24v power going to the control module and also check that all of the saftey controls are closed and completing the safety circuit...are you getting any flashing LED'S on the control module?

Coleman Propane... | Answered on Oct 21, 2011


Hi,

Here is a list of each common terminal and what their commonly used for. Alsolisted is what colors are commonly used. NEVER ASSUME these are what youhave. Verify all your wires by following each to each piece of equipment. Thiswill help you to be able to match your equipment with the terminal.

Here is the rest of the tip that I wrote...

Thermostat Wiring and Terminal Designations
heatman101If you have further questions, then comment back to me...

Coleman Propane... | Answered on Oct 15, 2011

Not finding what you are looking for?
Heating & Cooling Logo

Popular Tags

373 questions posted

Ask a Question

Usually answered in minutes!

Top Coleman Heating & Cooling Experts

Paul Carew

Level 3 Expert

3527 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

jdthefixer

Level 3 Expert

747 Answers

Are you a Coleman Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Coleman Heating & Cooling

  • Coleman Heating & Cooling

Most Popular Question

rollout limit switch keeps tripping

  • Heating & Cooling
Loading...