20 Most Recent
Fujitsu P50XHA10 50 in. Plasma Television - Page 6 Questions & Answers
How would you know if the remote control is faulty or not? for fujitsu 42 inch plasma monitor
Visit the site named 'Electro-help' for more
details. Click this link.
View it in 'Flip
card' option, which can be selected from the drop down box menu at the top left corner of the display window. It will make search easy. Some times, the ads attached with each
posts, both at the right and bottom, might help you to find the availability of
spare parts. There are more than 850
posts to different brand TVs now.
Pull up older posts there. A detail post about how to check a remote control is there one among the oldest.
9/28/2012 6:16:34 AM •
Fujitsu...
•
Answered
on Sep 28, 2012
Sound but no picture
I see so many here with no sound/nopicture issues:ISSUES: 1. IF sound main fuse/s are good.2. If no power or standby check main fuse, standby power supply and any signsof damage you can see---burnt parts etc.3. almost all these sets the troubleshooting involves
checking voltages on the main power board to narrow down theproblem.4. Be safe and if you do not know what you are doing don't open the set.Answers to issues:1. RE:fuses---if a blown fuse is found get a good replacement(not the genericones like Radio Shack). Many fuses are special even aside from amperage--Don'tput a higher rated amperage fuse in the set for any reason.2. RE: power supply in set: if total dead aside from main fuse the set uses astandby power supply that runs 7/24 and a main supply (some are combined andsome not.Here aside from checking fuses you want to examine all the filter caps on thepower/standby to see if any are puffed up or buldged up in some fashion--Iattach a photo of a good one---top should be silver metal and PERFECTLY flatand have no brown material coming out on top or bottom.What happens in the standby area is they use caps with too low a voltage rating(saves money) which causes them to fail in a year or two---the standby runs7/24 and the heat dries out the caps and they fail.3. Trouble shooting consists of the above and then at some point you have tobuy and try a board to see if it fixes it or not.4. Safety first--no TV set is worth getting injured or even killed over.
4/1/2012 3:22:11 PM •
Fujitsu...
•
Answered
on Apr 01, 2012
Remote for my fujitsu model
Hello
Three digit Universal remote codes for Fijitsu TV are:
046/ 197
Four digit codes are:
0197 0051
Direct Code Entry
- Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
- Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
- Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
- With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search
If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
- Manually turn on the device (TV, VCR, etc.) to be controlled.
- Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
- Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
- Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
- Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.
Codes for Fujitsu TV with RCA RCR3273 remote control are:
1228, 1027, 1186, 1229, 1045
OK.
8/8/2011 3:10:43 PM •
Fujitsu...
•
Answered
on Aug 08, 2011
After electrical storm no sound
sounds like you may have shorted it out. THERE is a built in surge protection on all standard new tv's unplugging the tv upwards of 30 mins can reset it . but if you do get picture i doubt that will help its probably blown speakers now.
3/28/2011 3:16:43 AM •
Fujitsu...
•
Answered
on Mar 28, 2011
We have just had a
What follows is a generic answer which applies to the majority of tv's.
Usually you need to cycle through the options which appear when you press the AV button on your tv remote control. Sometimes it's labelled as EXT instead and usually has a symbol of a box or circle with an arrow pointing into or out of it (sometimes a double-ended arrow).
If this fails, you need to recheck all of your system connections: it's not uncommon for installers to miss out a component when rushing to set up a new tv.
9/22/2010 2:11:00 PM •
Fujitsu...
•
Answered
on Sep 22, 2010
I have a 50" Fujisu
Hi
Thanks for using FixYa. From what you have described it seems to be the issue with Y board and the logic board should also be checked. These boards are located on the right side of the unit and to check them you’ll have to open the back of the unit. Once you have opened the back also check for any blown/bulged capacitors. All this is only recommended if you have electrical expertise & know how to solder/re-solder components as these units contain high voltages even when in off position. Please do accept the solution if the issue is resolved or post a comment for further assistance.
Thanks
Rylee
9/12/2010 9:13:03 PM •
Fujitsu...
•
Answered
on Sep 12, 2010
How to find ilo ip addr in windows operating
If you want to find the IP address that has been issued to your computer by a router or your ISP then :-
Click Start - Run - Type "cmd" and press Enter. Windows will then open a DOS command box, then type "ipconfig" and press enter. It will then display the IP addresses of all the network adapters on your computer. If you get IP address 0.0.0.0 then the network adapter/s didn't get issued an IP address from the router or the ISP.
8/13/2010 7:14:49 PM •
Fujitsu...
•
Answered
on Aug 13, 2010
My fujitsu plasma is not
Hi
Thanks
for using FixYa. A plasma TV is a very hard working device. It is
working harder than any TV that has been built before, and as a result it
produces a lot of heat. 75% of technical problems in plasma TV's are caused by
overheating problems. X, Y sustain, buffer boards controls
picture, fires the gas, and many others functions. When either of these boards goes
bad common problems include negative image, no image, vertical or horizontal
stripes on picture, turns on and than turns off, and many more. You’ll need to
open the back off the TV and check for any swollen/bulged/leaky capacitors on these
boards and replace whichever has gone bad. All this is only recommended if you
have electrical expertise & know how to solder/re-solder components as these
units contain high voltages even when switched off. Please do accept the solution if
the issue is resolved or else revert for further assistance.
Thanks
Rylee
2/7/2010 10:19:22 PM •
Fujitsu...
•
Answered
on Feb 07, 2010
Not finding what you are looking for?