Broksonic CTVG-5463GVC 19" TV - Page 4 - Answered Questions & Fixed issues

Have you tryed to go in to your TV menu and look for cable setup. Then change it to cable Not off air... Hope this was helpful.

Will you please provide more details about the problem you faces with this TV?

If you have the code book just hold the device you want to set uplike tv, vcdr, etc. and the power button at the same time. The power botton will stay lit. Put in your 5 digit code...hold it till the tv,vcr turnsoff. Turn it back on and try the rest of the functions. If it dose not workon certain function just hold down that key till that function works. Hope this helps.

These are the setup codes for Broksonic TV with GE universal remote control > 0147 0135 0250 0257 0310 0394

you should be able to get a remote for your model by sending a email request with what you need and the model number of your set to [email protected]

go to the main menu and select on the screen untill you reach to the language selection then select english as you purpose

Us the input button on the remote.

Only a LCD or a Plama tvs have the capabilities of the HDMI hubs to do the connections for the HDMI cable.Standard CRT tvs can't get HD signal or have the capabilities of the HDMI hubs for the HDMI cable to connected to it.

Hi,

Kindly mention the model number so that i could provide the link to buy the remote?

Thanks and Regards
taran_2005

hi there, it seems your TV is not that complicated to remedy. Try to check the power cord for any cut or open wire. also check the internal fuse if still works. if it has a burn appearance try to replace it with same type and amperage. if still not works focus on the power supply section if some capacitor are bulgy or deformed. worst is that you have a defective power MOSFET. this must be service by a technician. hope this help good day. please rate and vote.

You can follow the below links to order for the Remote:
http://remotes.com/remotes/servlet/rs?a=gmi&smodel=076N0HH010&brand_pn=BROKSONIC_076N0HH010&mode=large&v=1&uuid=A12991846721771
https://www.encompassparts.com/webwiz/wwiz.asp?wwizmstr=WEB.SEE&partnumber=5930579
You can order for the Operating Manual from the following link:

http://www.encompassparts.com/products/?SC20145-OM

When you try to program what??? usually you connect the XBOX OUTPUT to the same INPUT on the TV (RF ch 4 or 3), (RCA) yellow, white, red connectors or the RGB connectors, and for some newer 360 boxes you have the HDMI connector, it has nothing to do with the COMCAST CABLE unit... it is just a matter of having the correct cable/connections and the correct input set on the TV...


Good luck!

Hola, posiblemente el circuito integrado donde se realiza la seleccion de audio sea el problema y no el amplificador de audio ya que funciona con el DVD, habria que determinar cual IC realiza esta funcion tomando como referencia la salida demodulada de audio desde la etapa de frecuencia intermedia o adonde convergen todas las entradas de audio del TV.

Hi,

I have requested a copy of the manual and will upload it for you as soon as it is received. However, there is no guarantee that my request will be answered.

If you would like to request the manual yourself, please complete the simple form at the Hatzlachh / Broksonic website:

http://www.broksonic.com/ContactBroksonic.asp

Unfortunately, this manual is not currently available online - but with any luck it soon will be.

Regards,
BElectric

Testing remote control: The remote control puts out IR (InfraRed) signal that human eyes cannot see, to find out if the remote is sending out the signal or not you just point the remote at the digital camera's Lens (Digital Camera can detect IR), you should see flashing light on the camera's screen when any one of the remote button is pushed. If you do see the flashing on the camera, then the problem is in the TV IR receiver or the main logic board; more troubleshooting with scope will be needed to look at the signals. Parts: www.shopjimmy.com www.remotes.com

Basic LCD monitor troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you.

are you using bootleg dvds?some players will not play them.if this is not the case maybe something is wrong with your dvd

just through it away and get a new one

Clean the dirty optical drive with one of those commerical DVD cleaning kits they sell at the box stores. Also, could be the DVD is region specific. Region 1 is USA meaning the DVDs will only play on Region 1 DVD players. You can buy region free DVD players on e-bay for cheap.

Theres a reason they call these DVD players Broksonic. Because they are always Brok. Spend a few dollars and get a name brand next time, because they last longer since those companies invest more in R&D and quality control.

probably its finely out of tune, i would get onto settings then manually tune it myself. or if this fails.. call your service provider. its nothing that you have done wrong. its them. also. at the back of your television. make sure ALL essential leads are fully plugged in..

i found a remote at 1-800-remotes for $25.81 plus shipping