20 Most Recent
RCA P52926 52" Rear Projection Television - Page 5 Questions & Answers
Hi ,,my problem is one
This would be called a convergence defect. IT is not a real bad repair but it will have to be done by an authorized RCA repair shop. The alignment takes a jig called a chipper checker. Call around your area. WE charge about 250.00 to do this in columbus GA. THat should give you a starting point
Please leave feedback
Peoples heads are cut off
Since your tv is cutting the heads off durring regular or analog signal but not high deffinition sounds to me like you have to set the aspect ratio different or such as going to your picture format from the main screen. Play with the settings from zoom, full screen, no overscan, cinerama and see if this helps.
Picture seems a little dark
mine was like that only worked in a dark room so i pulled the back off and the lenses (3) were dusty cleaned them and it was fixed
Have a very old rca
It is either the projection lenses are very dusty or are getting weak.
I would clean the projection lenses and try it.
It has been a while, so bear with me.
The bottom speaker covers should should either have some screws around the edges or just pop off (most are the pop-off kind). Under there, there might be some screws that hold the bezel (that frame around the screen). Remove the screws and remove the bezel. You might have to slide the bezel up to pull it (try bumping up on the lower corners with the heel of your hand).The screen should come off with the bezel (just set it aside and be careful with it). Now the 3 projection lenses(red, blue, and green) and mirror are both exposed. Wipe the dust off the lenses with a damp cloth and follow with a dry cloth. If the big mirror is glass, clean it with a damp cloth (maybe a little glass cleaner) and dry with a clean cloth If it is the foil type mirror, clean it real gently with a damp cloth. The big white plastic lens at the front is cleanable with a clean damp cloth. But unless there is a smoker in the house, I wouldn't mess with it. If you do clean it, be sure to use a circular motion with the pattern on the lens...it scratches easily. Then snap the bezel/lens assembly back on and reassemble the front pieces.
It has been a while since I have cleaned one of these. There may be a few differences in getting into the projection area depending on the models. Since the projection tubes are aimed up , the dust really builds up in them.
Hope this helps and good luck with it.
I have an RCA P60752EB
hello am rico, first look for cold solder in your power supply, you need to open the back of your tv to do that. if you need more help, feel free to call me at anytime. 602-810-7149.
Why is there some sort
That will be the oil under the lenses to keep the tube screens cool. They leak over time and if it gets onto the electronice, it is conductive and will damage the circuits.
I have the 52 inch
hi,
you could try resoldering the vertical scan ic and changing electrolytic capacitors near it, as they have probably dried out due to the heat over the years. cant give you the position numbers as i have no manual but the ic should be on a heatsink on the deflection board,usually vertically mounted and with 5-9 leg.
ok
The TV comes on then
Sounds like a problem with the deflection circuit(possibly faulty horizontal and/or vertical deflection ICs and HOT). What is the status of the LED at the front after the unit shuts down? How many times does it blink?
When I plug the tv in it makes a beeping noise but
You are hearing the power supply trying to come up,but there is a short.....it almost like a chirping. More than likely,it will need a flyback transformer. A reputable repair shop can confirm and repair in the $200 range. If you have technical ability,I can guide you further
Stupid RCA TV....3D picture, 3
U replaced the one the middle out of the three?Yes,Still the same problems,just replaced all three convergence fuses caps than.Must resolders the FBT- flyback tranformer too.
I have convergence problem how do i repair
U have tools like a soldering iron,a desoldering pump or a roll desoldering braids,a roll of solders?Can u also know how to do basic soldering?Yes,than tries websites like Tvrepairworld.com,Tvrepairkits.com buy a convergence kit,belong to ur tv make and model,the kit also came with a instructional DVD also.How to fix ur tv convergence board.Or the shop,will cost u like $300-350 for parts and labors.
Picture problem with a rca home theater model p60752eb
I have a problem with the colors on my RCA Home Theater model #P60752EB. I believe it to be faulty tubes or something cause my green and my red color is messed up to the point it will not come in at all.what should i do to resolve this problem without replacing the tv
Not finding what you are looking for?