Top 20 RCA F19436 19" TV Questions & Answers

0helpful
1answer

Parental Control Code?

if you forgot your password you can reset it ,turn tv off press and hold vol< on tv and clear on the remote for 5 sec.,enter a new password next time you access the parental control menu.
4/16/2008 9:17:38 PM • RCA F19436 19"... • 464 views • 1 helpful votes
0helpful
1answer

Sparking rabbit ears

If the fuse blows the instant the power is switched on, there is most likely a heavy short in the primary side of the power supply. This could be the rectifier diodes or the switching transistor (or IC). If you do not have experience identifying and replacing shorted semiconductors, allow a qualified tech to handle it for you.
9/3/2007 12:42:18 AM • RCA F19436 19"... • 60 views • 0 helpful votes
0helpful
1answer

Sound

It could be a defective speaker or the audio output IC could be bad also. If your not a tech its a good Idea to seek a pro in the repair of a tv set as there are no user serviceable parts inside these set. Good Luck
6/30/2006 12:14:37 AM • RCA F19436 19"... • 54 views • 0 helpful votes
0helpful
1answer

Set will not turn on

If you're NOT still under warrantee you should at least open the TV and look for a blown fuse near where the power cable enters the set. A lot of times you can buy replacement fuses at a local electronic or hardware store and they're easy to replace. Check the fuse. If it is blown, it will be obvious and make sure that the set is unplugged before replacing it. If it blows again, or if it is not blown, your problem is probably in the 'X' volt regulator and you will need professional help with the repairs. good luck!
11/28/2005 9:27:32 PM • RCA F19436 19"... • 83 views • 0 helpful votes
0helpful
2answers

Rca rlded5098-b-uhd Backlight control

The actual LED strips have failed, chances of it being a board issue are slim, replace the backlights and all will be well
2/28/2023 4:17:51 AM • RCA Televison &... • 49 views • 1 helpful votes
0helpful
1answer

My Roku flat screen tv the original remote broke so I bought a RCA 3 universal remote and I can't get it to connect

Question edited for clarity. It is a 'Roku', not a 'ruko'. Roku is a streaming service and not a television manufacturer. The put their badge on a television made by an established maker that also has their streaming service built in, or with a set top/side dongle. https://www.roku.com/en-ca/products/roku-tv https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote You buy the remote SPECIFICALLY for the television you own. That is done by the model number. https://www.google.com/search?q=roku+television+replacement+remote ..
3/10/2023 12:20:28 AM • RCA Televison &... • 22 views • 0 helpful votes
0helpful
2answers

Having trouble with RCA tv vertical and horizontal lines can you help?

Generally horizontal lines are caused by a bad panel, there are COF IC's that give issues a lot of time and they aren't replacable.
3/6/2023 10:53:02 PM • RCA Televison &... • 22 views • 0 helpful votes
0helpful
1answer

My Kef psw2000 power on but but no sound,when i plug in RCA cable standby turn on,I think it's IC,pls what are the IC number for Kef psw2000

First off, even with the IC numbers are you going to be able to replace the faulty parts, in most cases it's not something that can be done without a soldering station, plus hot air station and advanced soldering skills, it's not like soldering a couple wires together. If you're able to replace them take the numbers off the top of the chips and cross reference them.
3/6/2023 9:05:45 PM • RCA Televison &... • 20 views • 0 helpful votes
0helpful
1answer

What is the code for a naxa DVD player ND-861

To program your RCA universal remote to control your Naxa DVD player ND-861, you will need to use the correct code for your device. Here are the steps to follow:

Power on your Naxa DVD player.

Press and hold the "Code Search" button on your RCA universal remote until the indicator light turns on.

Release the "Code Search" button.

Press and release the "DVD" button on your RCA remote.

Enter the code for your Naxa DVD player. You can find a list of RCA remote codes for Naxa DVD players in the RCA remote manual that came with your remote or by searching online. For example, the code for Naxa DVD players may be 3394.

Press the "Enter" button on your RCA remote. The indicator light on your remote will turn off if the code was entered correctly.

Test the remote to see if it's working. Try playing a DVD and using the remote to navigate the menu.

If the first code you tried didn't work, repeat the steps with a different code until you find one that works. If none of the codes work, it's possible that your RCA universal remote is not compatible with your Naxa DVD player.
3/6/2023 8:10:53 PM • RCA Televison &... • 19 views • 1 helpful votes
0helpful
1answer

RCA 4 DEVICE UNIVERSAL REMOTE, NEED 5 DIGIT CODE FOR DVP 3150V VCR DVD COMBO.

Please don't type is all CAPS, it is considered SHOUTING and is harder to read. Thanks. No one buys Universal Remotes, you buy a remote made for the device, a copy of the original. https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote

Genuine PHILIPS NA725UD DVD VCR COMBO Remote ...

eBay https://www.ebay.com > itm Genuine PHILIPS NA725UD DVD VCR COMBO Remote DVP3150V/37 ; Type: Remote Control ; Manufacturer Warranty: None ; Custom Bundle: No ; Color: Gray ; Model: Philips. MPN: DVD740VR99 DVD74DVR, DVD740 DV... Compatible Brand: For Philips Compatible Model: DVP3150V/37 US$49.91 · ‎In stock
3/10/2023 11:45:35 PM • RCA Televison &... • 17 views • 0 helpful votes
0helpful
1answer

I have a RCA tv model No led46c45rq with no picture , but does have sound

The HDMI cables need to be replaced and does not work for your TV.There is a problem with your TVs HDMI cables.
2/2/2023 3:06:14 PM • RCA Televison &... • 28 views • 0 helpful votes
0helpful
1answer

I have a RCA dvd home theatre system rtd317 & the tray opens & closes with or without a disk & won't read the disk.

If your RCA DVD home theatre system RTD317 tray is opening and closing without reading the disk, and you've tried unplugging it, cleaning the laser lens, and the motor doesn't seem to be working, it's possible that there may be an issue with the motor or with the disk mechanism itself. Here are a few troubleshooting steps you can try:
  1. Check the disk: Make sure that the disk you are trying to play is clean and free of scratches. Sometimes a dirty or scratched disk can prevent the player from reading it.
  2. Reset the system: Try resetting the system to its default settings. To do this, unplug the unit from the power source for a few minutes, then plug it back in and turn it on.
  3. Check the motor: When the tray closes, listen closely to see if you can hear the motor spinning. If you can't hear the motor, there may be an issue with the motor or with the power supply to the motor. In this case, it may be necessary to have the motor replaced.
  4. Check the disk mechanism: If the motor is working but the disk still won't spin, there may be an issue with the disk mechanism itself. In this case, it may be necessary to have the disk mechanism repaired or replaced.
  5. Contact customer support: If none of these steps work, it may be best to contact the manufacturer's customer support for further assistance or to have the unit repaired by a professional.
Remember to always follow the manufacturer's instructions and safety guidelines when working with electronic devices.
2/19/2023 1:37:15 AM • RCA Televison &... • 21 views • 0 helpful votes
0helpful
1answer

RCA LED 50B45RQ tv turns on, lights up screen, but screen is solid blue.

It sounds like you may have an issue with the backlight of your TV. If a backlight is not getting adequate power, it can cause the screen to appear blue or have "flashing white splotches". The best way to resolve this issue is to have a qualified technician inspect the TV to determine if there are any issues with the backlight power supply. If there is an issue with the power supply, they will be able to replace it and resolve the issue.
2/22/2023 5:17:08 AM • RCA Televison &... • 20 views • 0 helpful votes
0helpful
1answer

Model LED32B30RQ need 4 digit code to program universal remote. RCA TV

The 4-digit code to program a universal remote to work with a RCA LED32B30RQ TV model is likely to be one of the following: 11447 11758 11442 To program the universal remote to work with the RCA LED32B30RQ TV:
  1. Turn on the TV
  2. Press and hold the "Setup" button on the universal remote until the "TV" button blinks twice.
  3. Press the "TV" button on the remote.
  4. Enter the 4-digit code for your TV using the number buttons on the remote.
  5. Press the "Power" button on the remote. The TV should turn off.
  6. Press the "Setup" button again to lock in the code.
If the TV does not turn off after entering the code, please try the other codes listed above. If none of the codes work, you may need to refer to the universal remote manual or contact the manufacturer for further assistance. Note: The method to program the universal remote may vary depending on the remote brand and model
1/22/2023 2:47:56 PM • RCA Televison &... • 29 views • 0 helpful votes
0helpful
1answer

I have an RCA remote for an old RCA DVD player. The remote is not working.

If you point it at your camera on your phone, if it is transmitting, you will notice the remote flashes. Either way it is probably faulty and a replacement is required.
1/29/2023 4:02:47 PM • RCA Televison &... • 25 views • 1 helpful votes
0helpful
1answer

My RCA TV model RLDED3258 HAS A ERROR SAYING NO SIGNAL.

  1. Check the cables: Ensure that all cables are securely connected to the TV and to the device you're trying to connect. Make sure the cables are not damaged or frayed. Try a different HDMI cable to see if that resolves the issue.
  2. Check the input: Make sure the input you are using is selected on the TV. You can usually do this by pressing the "Input" or "Source" button on your remote control.
  3. Check the device: Make sure the device you're trying to connect (such as a DVD player or cable box) is turned on and that it's set to output video to the TV.
  4. Check the TV's settings: Some TVs have a setting that allows you to select which type of device you are connecting (such as a DVD player or cable box). If your TV has this setting, make sure it's set correctly.
  5. Restart the TV: Sometimes simply restarting the TV can resolve the issue. Turn off the TV and unplug it from the power source for a few minutes, then plug it back in and turn it on.
If none of these steps resolve the issue, then it may be necessary to replace the logic board.
2/11/2023 4:20:04 AM • RCA Televison &... • 19 views • 0 helpful votes
0helpful
1answer

Hello. I have a RCA LED50B45RQ TV that has standby light illuminated when turned on with remote white flashes on left side of screen for a couple seconds with no audio or video.

Your RCA LED50B45RQ TV appears to have a problem with the display and audio. When the TV is turned on and the remote is used, the standby light illuminates, and the screen flashes white on the left side without audio or video. Various factors could be to blame for this problem. A few troubleshooting tips are provided below:
  1. Check the connections: Make sure that all the connections between your TV, cable box, or streaming device are securely plugged in.
  2. Check the settings: Ensure that the TV is set to the correct input and that the cable box or streaming device is set to the correct output.
  3. Check the backlight: Some TVs have an adjustable backlight setting. Ensure the backlight setting is turned on and set enough.
  4. Check the cable: If the cable that connects the TV to the wall outlet is damaged, the TV won't turn on. Try unplugging the TV, waiting a few minutes, and plugging it back in.
  5. Check the power supply: The power supply could be malfunctioning. It could be damaged or not provide enough power to the TV.
  6. Check the Main Board: The main board controls all TV functions. It could be malfunctioning, which is causing the TV not to turn on or display correctly.
  7. Contact the manufacturer: If none of the above solutions work, it may be necessary to contact the manufacturer for further assistance. Your TV may require repair or replacement.
12/20/2022 3:48:19 PM • RCA Televison &... • 47 views • 0 helpful votes
0helpful
1answer

How do I program sharp remote to RCA tv

You can program a Sharp remote to an RCA TV by following the instructions in the user manual.
2/4/2023 1:41:12 AM • RCA Televison &... • 20 views • 0 helpful votes
Not finding what you are looking for?
RCA F19436 19" TV Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Jaime Hernandez

Level 3 Expert

2351 Answers

Cindy Wells

Level 3 Expert

6609 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

RCA Televison & Video

  • RCA Televison & Video

Most Popular Question

parental control code

  • Televison & Video
Loading...