Top 20 RCA HD52W58 52" TV Questions & Answers

If you wish to get some details; visit the site linked here. Pull up older posts. https://electronicshelponline.blogspot.com/ faults & possible causes to LCD & Plasma screen are given with illustrations. You can get an idea about the fault to an extent. Faults to all LCD & Plasma screen are similar, irrespective of its brand and screen size. Search the site by type in the "BRAND NAME" of your device; (Exclude the model number), in the "Search box at the top right of the display window of the Homepage" to get gathered related posts

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/ If blinks continue without any pause, the main board is faulty.

Tube burnt out

If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order. Pull up older posts. Surf the site with patience. http://remotesearch.blogspot.com/ http://electrohelponline.blogspot.com/

Many conditions can cause this...too many to be specific. A short on the circuit board, thermal protection opens when too much heat trips the fuse. A bad power supply, leaking tubes, dirt/dust collection on main board, etc.

What is the problem you faces with its sound? Provide more details; please. did you checked all the sound settings. Check the speaker/s first. If found OK; check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Surf the site with patience. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box. http://electronicshelponline.blogspot.com/

Flashes of this light are fault indications. From the number of flashes occurs at one time switch ON, you can get an idea about the faulty circuit stage inside it. Count this number carefully after switch ON power at one time, and if you wish to get more details check the site linked here. It has details about these blinking codes to many brand TVs. http://electronicshelponline.blogspot.com/ Pull up previous posts or type in the brand name and model number to of your set, to its search box, and press 'Enter' or view it in Mosaic / Timeslide option.

PJ 42 how to fix it

hi I want to repair my changhong tv,,how much pay to service?and where to call

I suggest you replace the TV as the cost to repair this is about $700.00

Google the model number of the remote being tried for a "manual" which will have instructions and a list of POSSIBLE codes for the set you want to use it on--note that not all remotes will program for all sets.

HDMI is sensitive---if hooked up with set or source for signal it can act up---also if using a box for the signal the box can act up---usually if box is unplugged for a while and plugged back it may reboot and work again.If the model number here is correct the set should also have a component input for HD---can go that way if it has that.

try to resolder the fly back transformer.

The best assumption, at this point, is that the power supply board has died. You can buy a replacement unit from the link below and have it professionally installed.

Power Supply

Try the following- Before you turn it on, set a large fan ("breeze box") or similar behind the set and aim it toward any lower openings you see.
If this lengthens the time before it shuts down, then a cooling fan normally found in the lower cabinet area is not running. Those sets can have significant hot areas and may have a thermal shutoff to prevent fire in case of a fan failure.

which model remote u r using plz give pic of the remote then we can give u a solution

I would suggest you goto The RCA website and download the User Maunual.. Here is the URL.. http://tv.rca.com/product/downfiles/UM-55LA55RS-English.pdf I know it say its a 55inch, but, it should help you OK..
Hope this helps.

Unfortunately, the Input button (to change the source from INPUT 1, INPUT 2,
INPUT 3, INPUT 4, Front Input, HDMI/DVI, and last-active channel) is only on the remote. If your universal remote was built 6 months after the TV was released, try a different code for RCA/Thomson TVs (assuming the remote has an input or source key). Thomson built the TV.

If your universal remote doesn't have an input key, you probably need a higher end remote (one with that key or one that can be programmed from a computer). Alternatively, you can get an exact replacement remote here: http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&uid=0&m=HD52W58&uuid=12927154203570 .

I hope this helps.

Cindy Wells

RCA 52W58's are notorious for having a capacitor problem. I have repaired many of these and the part only runs about $4.00. All I can remember is the cap is on the D board.

Hello, Is after the TV turns on, it continues to work as usual