20 Most Recent RCA RCR350 Remote Control Questions & Answers

0helpful
1answer

My remote stopped turning the

It's rare to see an IR sensor go, it's most likely a defect with the remote itself. If you have a remote you can test with the tv, that's probably the idea solution. If you don't, you can possibly check out a site like http://www.remotecontrolhookup.com and order a new original remote and give that a try. If that doesn't work, you can always return that new remote and maybe look into buying a new TV, because repairing it may get expensive.
5/29/2013 12:26:03 AM • RCA RCR350... • Answered on May 29, 2013
0helpful
1answer

I lost the remote to my television. It is an RCA

Maybe you can try purchasing the original RCA remote from a site like this: RemoteControlHookup.com
5/29/2013 12:15:23 AM • RCA RCR350... • Answered on May 29, 2013
0helpful
1answer

Step by step

What steps are you looking for? Also what is the problem? Also this may solve your issueCopied from: voxrightnowProgramming the Remote:Your universal remote can operate a variety of brands of components. In order for your universal remote to control your components, you need to program the remote with the codes that match the components (See Code List below). These codes enable the remote to communicate with your components. Each brand and each component has its own "language," and, by programming the correct codes into your remote, you tell the remote to "speak the same language" as your components.There are two methods you can use to program your remote control to operate your components: Direct Code Entry and Manual Code Search and Entry. Most components can be programmed in one of these ways. Try them in the order listed.In order to control combo TV/VCR or TV/DVD units, you must program both the TV key and the VCR•DVD key. Once programmed successfully, the TV key controls the TV functions on your unit, and the VCR•DVD key controls the VCR or DVD functions. There is a specific section in the Code List for combo units. The codes in this section should be tried first, using Direct Code Entry on the TV and VCR•DVD keys. If this is unsuccessful, follow the normal programming methods for both the TV and the VCR•DVD keysDirect Code Entry:To program your universal remote to control your components using the Direct Code Entry Method, follow the steps below.1. Manually turn on the component you want the remote to control (TV, VCR, DVD, satellite receiver or cable box).2. Find the Code List below. Find the list for the component you wish to program. Find your component's brand. You will see a listing of four-digit codes for each brand. If your brand isn't listed, use the Manual Code Search method to program the remote control. (Refer to page 5 in the User Manual for Manual Code Search method, or scroll down in this Answer to the next section.)3. Press and hold the component key (TV, VCR•DVD, SAT•CBL) you wish to program. The LED indicator light turns on and remains on. If you release the component key any time during the Direct Code Entry procedure, the LED indicator light blinks four times, and the process is exited.4. While holding down the component key, consult the Code Lists for the four-digit code that corresponds to your component's brand and use the number keys (0-9) on the keypad to enter it. While you are pressing the numbers, the LED indicator light turns off.5. After the fourth number is entered, the LED indicator light turns on. At this time, release the component key. If the LED indicator light turns off, you have entered a valid code and have followed the correct procedurefor Direct Code Entry. If you enter a code number that is not in the Code Lists or you do not follow all of the steps for Direct Code Entry, the LED indicator light blinks four times when the component key is released. This is an indication that a programming error has occurred. In that case, repeat the Direct Code Entry process from step 3 and try the next code listed. The last programmed code under that component key is retained. Throughout the programming of each key, be sure to keep the remote pointed at the IR sensor of the component you are currently programming the remote to control.6. To confirm that the component key is programmed with the correct code for maximum functionality, test the component. Attempt to control a variety of the component's functions with the remote. If some of the features of your components do not work, try programming the remote with a different code in the list until you find the code that allows the remote to control the majority of your component's functions. Different codes can provide different levels of functionality.Manual Code Search and Entry:If your component's brand isn't listed in the Code Lists, or if you have tried all of the codes for your brand and the remote does not operate your component, try the Manual Code Search. This Code Search method cycles through all of the codes in the Code Lists in the event that your component's code is listed under another brand. The Manual Code Search method may take a long time because the remote searches through all of the codes in its memory for the code that operates your component. Therefore, if your brand is listed in the Code Lists, first try the Direct Code Entry method described on page 4 in the User's Manual also described above.NOTE: To exit without saving any point in the Manual Code Search, press and release the GO BACK key.1. Manually turn on the component you want the remote to control (TV, VCR, DVD, satellite receiver or cable box).Note: If you press an invalid key during the Manual Code Search, the remote does not respond and the LED indicator light does not blink. If you do not press a valid Manual Code Search key (TV, VCR•DVD, SAT•CBL, ON•OFF, GO BACK), the search times out after two minutes. When the search times out, the LED indicator light blinks four times and turns off. The last programmed code under that component key is retained.2. If you are programming the remote to control your TV or satellite receiver, go directly to step 3. To program the remote to control a VCR or DVD follow the preprogramming method listed below. Preprogramming the VCR/DVD Key The VCR•DVD key can control only one component, either your VCR or your DVD. To program your remote to control either your DVD or your VCR, you must first put the remote in the proper programming mode. Follow these directions before proceeding to step 3. a. Press and hold the VCR•DVD key. The LED indicator light turns on. b. While holding down the VCR•DVD key, press and release the number 2 key on the keypad to control a VCR or the number 3 key to control a DVD. The LED indicator light turns off. c. Release the VCR•DVD key. The LED indicator light blinks four times and then turns off. Your remote is now either in VCR or DVD Programming Mode, depending on which you chose. Proceed to step 3.3. Press and hold the component key (TV, VCR•DVD, SAT•CBL) you wish to program. The LED indicator light turns on and remains on.4. While holding the component key down, press and hold the ON•OFF key. The LED indicator light turns off.5. After holding down both keys for three seconds, the LED indicator light turns back on.6. Release both keys. The LED indicator light remains on. Throughout the programming of each key, be sure to keep the remote pointed at theIR sensor of the component you are currently programming the remote to control.7. Press and release the ON•OFF key repeatedly until your component turns off. Each time you press the ON•OFF key, the LED indicator light blinks, and the next code in the list is sent. This process continues until all of the codes in the Code Lists have been searched. If your componentturns off, you have found the correct code. (If it cycles through and the LED indicator light blinks four times and turns off, all codes have been searched. The Manual Code Search method is exited.) Because there are so many codes, you may have to press the ON•OFF key many times-possibly up to 200 times.8. Once you have found the correct code, you must save the newcode by pressing and releasing the STOP key. The LED indicatorlight turns off. You must press the STOP key to save the code or the correct code will not be stored!9. Once you press the STOP key, the code is stored.Testing the Code for Maximum Functionality:1. Once the code has been stored (see Manual Code Search and Entry Method above), use the remote to attempt to control a variety of the component's functions. If the code that has been stored controls the majority of the component's functions, programming is complete. If thecode stored does not give maximum functionality, you will want to try another code.2. In that case, repeat the Manual Code Search and Entry Method from step 1. When the component turns off for the first time, do not press the STOP key, which would store the code. Instead, with the unit now off, continue to press the ON•OFF key repeatedly until the unit turns back on. Once the unit turns back on, you have found another code that operates the component. Press the STOP key.3. Test the functionality again by attempting to control a variety of the component's functions. If the code that has been stored controls the majority of the component's functions, programming is complete. If the code stored does not give maximum functionality, you will want to try another code.4. Repeat the Manual Code Search and Entry Method from step 1. Each time a code turns the component on or off, you have found a code that operates the remote and needs to be tested for maximum functionality. Continue through the code lists, cycling through the codes you have already tried, until you find one that offers maximum functionality.
11/10/2012 9:31:34 AM • RCA RCR350... • Answered on Nov 10, 2012
0helpful
1answer

How do I program my rca universal remote model number rcr350?

These are the general proceeding for RCA remote controls set-up:1. Manually turn on the device youwant to control.2. Find your device's brand in theBrand Code list section of theaccompanying code list. Circlethe number for your brand andkeep the list handy.3. Press and hold the device key you want to program. ThePOWER key illuminates.While you're holding down the device key, use your otherhand to press and hold the remote's POWER key at thesame time. The POWER key turns off.4. Wait until the POWER key comes onand stays on. Then release both keys5. Look at the numbers you circled foryour device's brand code number.Press those numbers on the remotekeypad.Note: For single-digit brand codes,press the 0 key first (for example, 0-5for 5).6. Point the remote directly at thefront panel of the device you wantto control. Press POWER on theremote and wait 2 seconds. Theremote is testing a single code foryour device's brand.
8/2/2012 3:34:54 PM • RCA RCR350... • Answered on Aug 02, 2012
0answers
0helpful
1answer

I changed the batteries in

Try this site I believe it will help you a lot..Just click the link..Hope it will help you..
7/12/2011 3:11:31 PM • RCA RCR350... • Answered on Jul 12, 2011
0helpful
2answers

Have no instructions to set to my sears tv need to

This Web page should allow you to find the codes for any devices you want to add for this remote.http://remotefinder.rca.com/default.aspx?site=rca
Other than that there is an easy way to program this remote.

1. Turn on the device by hand.
2. Hold down the device name key.(hold the TV button to program a TV)
3. While holding down this key also hold down the power key until the red light turns off and comes back on. Then release both buttons.
4. From here hit the power button repeatedly until the device turns off.
5. Hit the stop key at the bottom. Now the remote is programmed for that device.
5/5/2011 5:19:42 AM • RCA RCR350... • Answered on May 05, 2011
0helpful
1answer

Cant progam not understanding the

The best way to program with this remote is to follow these instructions.
1. Turn the device you wish to program on by hand 2. Press and hold the key for the device you are programming. (If it's a TV hold the TV button etc.) 3. While holding the button down, press and hold the power button down until the light turns off, and then back on. Once the light is back on release both keys. 4. Now, while pointing the remote at the device, hit the power button until the device turns off. Once the device turns off, you have found the right code. 5. Hit the stop button on the remote in order to save the code, and program the remote to that device.
This should work for most universal remotes these days. It might take you a long time to find the right code as well, the code list is very long so you just have to keep chugging through them. I've reprogrammed this type of remote many times and have hit the power button for over 5-10 minutes before the device turns off. Best of luck to you.
5/5/2011 3:01:20 AM • RCA RCR350... • Answered on May 05, 2011
0helpful
1answer

I don't know how to reprogram it and it doesn't

try this

  1. Manually turn ON your device (TV, VCR, Cable Box)
  2. Press and "HOLD" CODE SEARCH
  3. Press and release the device button you want to set up (TV, VCR, Cable Box) However, if you are using AUX for a device, press and release AUX first and then the device button for the type of device to be programmed (TV, VCR, or Cable). The selected device button will flash once.
  4. Release CODE SEARCH.
  5. Press OFF/ON repeatedly until the device turns off (you may have to press up to 100 times at a rate of once per second).
  6. Once the device turns off, press and release ENTER.
  7. With the device on, press any other button. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-6
2/27/2011 5:46:46 PM • RCA RCR350... • Answered on Feb 27, 2011
0helpful
1answer

Forgot how to program their is no code button

http://voxrightnow.custhelp.com/app/answers/detail/a_id/7732/~/programming-the-rca-rcr350-universal-remote-control should give you your answer. Access to code lists and product manual are also provided at the bottom of the web page.
2/22/2011 6:38:29 AM • RCA RCR350... • Answered on Feb 22, 2011
0helpful
1answer

I need a code for

1/22/2011 3:06:56 AM • RCA RCR350... • Answered on Jan 22, 2011
0helpful
1answer

I have a Dayteck TV and i have lost the remote in

Hi - For Dayteck plasma remote use Daewoo remote R-V2A.
Has same functions.I bought one from ( www.discount-merchant.com) for $19.99 and cust. was very happy.
[email protected]
1/5/2011 10:11:02 PM • RCA RCR350... • Answered on Jan 05, 2011
0helpful
1answer
0helpful
1answer

Unable to locate code

10/30/2010 6:53:00 PM • RCA RCR350... • Answered on Oct 30, 2010
Not finding what you are looking for?
RCA RCR350 Remote Control Logo

95 questions posted

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76823 Answers

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

Cindy Wells

Level 3 Expert

6394 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

RCA Televison & Video

  • RCA Televison & Video

Most Popular Question

re program

  • Televison & Video
Loading...