Orange SPV M1000 - Answered Questions & Fixed issues

Hi to get codes visit mobileunlocksolutions.com here they ask you the imei number of your spv m1000 mobile .finally they send you codes to unlock your mobile .then visit mobileunlockguide.com here they provide free instruction guide about how to enter codes in your mobile.

Hi to get codes visit mobileunlocksolutions.com here they ask you the imei number of your spv m1000 mobile .finally they send you codes to unlock your mobile .then visit mobileunlockguide.com here they provide free instruction guide about how to enter codes in your mobile.

ask your sim card by calling them or go to them close store to give you your puk code right now

A request for a PUK code ("Personal Unlocking Key") will appear on your phone if your SIM card PIN code is entered 3 consecutive times incorrectly.

Your SIM card will then become "PUKed" or Blocked. This is a security measure to protect your service.

You need to call the Customer Service department of your cell phone provider and they will give you the PUK code which will unblock your SIM card.

Hi,


PIN CODE is SIM dependenet and not phone dependent

PUK code in PIN UNLOCKING CODE, which is required when you give PIN number wrongly for 3 times,
This code is OPERATOR specific and not phone specific and you have to call you operator and get PUK if PIN is blocked...

if you provide PUK code wrongly for 10 times, you sim may become useless, then you have to buy new SIM

NOTE: You should ask your service provider,get the PUK,


ENJOY! RATE THIS SOLUTION
RNJ VINOD KUMAR

http://www.loadstone-gps.com/docs/gps_manuals/m-1000.txt

You must have either ActiveSync (for Windows XP) or WMDC (for Vista and 7) and WMP installed and running on your PC. Whenever your device is synchronized with your PC, the device' storage card should become visible to WMP, whose sync tab will allow you to synchronize its library with the storage card.
Just my 2 cents... Carlos

Do not enter any code into your phone. The PUK code is a code that your service provider has and not one that you would know or have in your manual. If your an AT&T customer they do provide PUK on their website. If you have entered in a code and the phone is now saying PUK blocked you'll have to go to store to purchase a new SIM card.

u need SD wifi card

http://www.maplin.co.uk/Module.aspx?ModuleNo=99452&C=Froogle&U=99452&T=Module

there could be a problem with the infrared emiting device. ensure the infrared is emited normally, how to see this infrared beam? read more at: http://www.unique-stuff.co.cc/fixing_remote_control_check_infrared.html

PUK code can be given only by your service provider which is specific for each and every mobile number.
Contact your sim customer care department over phone. Its free of cost to get the pin or puk no. If you cant contact through your phone get some other phone and contact them.
Go to the nearest service outlet of your service provider they can also help you.
There is no other go than the above procedure only your service provider cangive it nobody else in this world nor any software.
Go to the below link and you can confirm that the above procedure works and there is a testimonial given by the customer too. http://www.fixya.com/support/t3582685-phome_lg_ke670_put_security_code_phone

Hey, seems your operateing system is corrupted in the flash memory.

solution 1

Reflash the operateing system. If you have the knowledge on how to do so.

2. Take it to the shop where you bought it for repairs and analysis motherboard might be damaged.

Good luck.
If you need more asistance, let me know.

Contact your service provider, they set the PUK code.

you can call to your network provider customer care. They will give you PUK code and PUK2 code for you.....Hope this will helps you....Thank you...

Found sims are usually bad. Don't risk damage to your cell.

The puk code is sim card spesific it comes with the sim card when you get it or you can get it by calling your phone service provider of the sim card to get the puk code.
if you have entered the puk code wrong too many times you will make the sim card useless and you will have to contact your phone service provider for a new sim card, it will probably cost.

I fixed it! Instead of selecting "connect to all available networks," I selected "connect to selected access points."

Put it on bootloader then try to update it again.if its not work then you have to find a same device and copy rom image to sd card then you can flash from sd card to your bricket with bootloader....good luck

hi there

download file from here for step-by-step guide to replace the M1000's screen yourself

All the Best.

Was this solution helpful? Show your Appreciation by rating it:

hi there

download file from here for step-by-step guide to replace the M1000's screen yourself

All the Best.

Was this solution helpful? Show your Appreciation by rating it: