20 Most Recent
Bush 5693D 24" TV - Page 4 Questions & Answers
Tv will not come on
This is the best solution for your problem as a 40 year experience with wires etc.
Go to the source of your cable signal connector .
Open it and clean the terminals with emery paper , sand the end of the cable shiny clean from corrosion , get a new barrel connectors with gold terminals if possible lengthen the ends of the cable , insert and tighten good, use thick rg-16 or rg 40 cable with good insulation ends crimped professionally with a crimpier or buy ready made , not from dollar store. Get a gold plated professional splitter if you need one or two , it will cost about 15 or more each . Make the cable runs as short as possible, using the thick good cables. If needed get a signal magnifier. From radio shack or the source etc. Connect them good and tight . Ground the splitters . Problem solved , you will get crystal clear channel 2 to 7 including 3 and 4 . Isolate the TV cable from other cables and power wires.
Vitally
When tv is turned on it takes 35 minutes for the
u have to replace apart inside the tv (picture tube base)
which connects picture tube to circuit board,,, call aservice pro...the symptoms are blurry picture & after some time picture gets clear
Tv will not display laptop . it says
Hi, you need to go into your video card settings in your laptop and change the display to TV or there may be an option to have both on at the same time..
Which laptop is it you have?
Let me know - Anthony
Kids lock the perental control wanna no if they is
There's only one way,...
You need to open the case, then look at the second biggest IC's, it used for programing, and always in front of the board, not in the middle.
After locating it, look near that IC, there's a tiny IC with 8 pins ( 4 left, 4 right), it size only 8mm x 12mm.
If you found it, replace it with the same parts and number.
No picture only a blue screen
A blue screen usually means no signal is recieved or supplied - try changing channels to ch. 3 or hooking up a dvd player, if available, to video inputs and select that input on the TV.
Bush tv has a circle on screen like looking thru a telescope
HELLO
Funnily enough I have been given a 21 inch standard Bush set with the same problem!
It's a DEGAUSSING fault. This means the deguss circuit in the TV is not operating as it should - probably a faulty positor. When you switch the TV on (NOT FROM STANDBY) the circuit that removes magnetism from the screen does not work correctly.
Switch it off, unplug the set from the mains for 30 minutes or so and try it again. If there is no change, contact a TV repair centre.
Make sure there are no hifi loudspeakers next to the TV or a radiator as this can have an effect too.
ALL THE BEST! (:-)
Dont know my model number?
HELLO
You will find the model number on the back of the TV. It's usually a square white sticker with all the info of the set (chassis type, model number, power rating etc).
When you have all the info, go on the web and do a search and I'm fairly certain you'll find a replacement. A generic type will do all the functions of your original - unless you want an original one of course! But I would advise against cheap code type remotes that will not do everything. (:-)
My tv is picture is blue and green
Hi there my t.v has a similar problem, I turned it on and the colours arn't right, there the colours go out in three circles mainly mainly blue, green, red yellow, but depends whats showing on the t.v? Please help.
Picture quality
I have over 10 years experience in electronic tech support.
I
know this isn't what you want to hear, but the problem you've described
can't be fixed with troubleshooting. Your TV will have to be repaired.
There is a part that has developed a defect and needs to be replaced. Before paying a TV
repair person $75+ to diagnose the problem, ask yourself if you're
willing to pay $150 minimum to fix this particular set. Also keep in
mind that if the TV is three years old or more replacement
part(s) availability maybe limited.
Normally it will cost at least $75 to have the
set looked at by a repair shop (diagnostics). If the part needed to
complete the repair isn't available, you won't get that money back.
I hope I've provided you useful assistance and that this information
allows you to make an informed decision as to how to proceed from here.
I hope I've earned a positive rating from you today.
Please let me know if I can be of further assistance.
BUSH LCD 27 inch
The TV is on protect mode.
Try first leaving the TV power cord unplugged for some times, let say one hour or so.
Also
ensure that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem with no receiver box
or dvd connected.
If that does not work, and you keep having a flashing
led on front of the TV, and tv turning off by itself after a while,
that indicates a fault condition.
The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.
1The
internal circuits are jammed because of electrostatic
charges accumulating on capacitors, or because of a wrong voltage read
by the main chip on your monitor controller board. this started the
protection circuit.
2 The protection circuit detected a wrong
voltage or abroken contact, identified an internal fault and kicked in
, startingthe flashing light.
If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.
If you are in situation 2 , then there is an internal fault.
Common faults
that can occur are a blown capacitor on power board, a
convergence IC has blown, or a fault on Digital board.
Check also
the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you
can get same flashing state because of the video cable.
If under warranty contact the manufacturer ringing the number on the user manual
If you want to repair at your own expenses, just locate any good qualified repairer.
Not finding what you are looking for?