Filter Queen Defender Air Purifier - Answered Questions & Fixed issues
Red light
Here is the link to the user manual;
http://www.filterqueen.com/pdf/defender.pdf
The red light indicates a filter needs replacing, see page 6 of the manual (page 9 of the pdf file)
If filters have been replaced and the light still flashes, then the reset procedure (described on the same page) should work.
If still flashing then there is a more serious, but probably fixable fault.
Hope this helps - ask again if you need more info :)
12/14/2015 7:47:04 PM •
Filter Queen...
•
Answered
on Dec 14, 2015
•
952 views
Where can I get a new electric cord
What are you looking for? If is just for house current for average use go to any well known hardware or places like Lowes or Home Depot or Sears..ask for or look 14 gauge on the tag..if for higher amp use such as portable air conditioners and 15--3000 watt portable heaters ask or look for 12 gauge wire..that should handle all your needs..good luck...
10/2/2014 8:40:45 PM •
Filter Queen...
•
Answered
on Oct 02, 2014
•
99 views
Replace air filter warning light to reset?
1. Plug unit into outlet.
2. Press power ON/OFF switch to the ON position.
3. Allow unit to start running at low speed.
4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink.
5. Release both the UP and DOWN arrow buttons.
6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.
1/22/2014 7:05:16 PM •
Filter Queen...
•
Answered
on Jan 22, 2014
•
756 views
Filter Queen Defender red light will not blink
no with the red lite on it mean that you need to change your filter its a safety feature so you dont burn out your motor and also so you dont blow unpurified air through out your home
8/3/2018 11:00:00 PM •
Filter Queen...
•
Answered
on Aug 03, 2018
•
1,291 views
How do you reset the
Filter Replacement
Filter Replacement Indicator:
Your Defender® is equipped with a Filter Replacement Indicator located on the front
panel. Anytime this red indicator flashes, it is recommended that you call your authorized
FILTERQUEEN® Distributor to order a replacement filter. Anytime this red indicator stops
flashing and remains solidly illuminated, it is recommended that you change your filter. To
receive full benefit from your Defender® and to extend your warranty, it is strongly
recommended that you follow the filter replacement schedule suggested above. Under higher
pollution levels, your filters will need to be replaced more frequently.
The Filter Replacement Indicator is operated by filter time in use and is controlled by an
onboard timer. After 11 months of time in use of your Medi-Filter® Cartridge, the Filter
Replacement Indicator will begin to flash. It will continue to flash until the you reach 12
months of time in use, at which time the Filter Replacement Indicator will stop flashing
and remain solidly illuminated.
After replacement of your Medi-Filter® Cartridge, you must reset the Filter
Replacement Indicator's timer. When the timer has been properly reset, the Filter
Replacement Indicator will turn off.
Resetting the Filter Replacement Indicator Timer:
After replacement of your Medi-Filter® Cartridge per the instructions found on page 7, the
Filter Replacement Indicator's timer can be reset by performing the following sequence of
steps:
1 Plug unit into outlet.
2 Press power On/Off switch to the On ("I") position.
3 Allow unit to start running at low speed.
4 PRESS and HOLD both the Up and Down arrow buttons until the Filter
Replacement Indicator starts to blink.
5 Release both the Up and Down arrow buttons.
6 While the Filter Replacement Indicator is still flashing*, again PRESS and
HOLD both the Up and Down arrow buttons until the Filter Replacement
Indicator turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will
turn off and not flash again for 11 months. If the Filter Replacement Indicator remains
on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when
the buttons are pressed the second time. The Filter Replacement Indicator will continue
to flash for approximately 3 seconds after the buttons are released as required in step 5 above.
Note: Under higher pollution levels, your filters will need to be replaced more frequently.
Note: To order replacement filters, call your authorized FILTERQUEEN® Distributor, or call
1-440-846-7800 for the Distributor nearest you.
http://www.filterqueen.com/pdf/defender.pdf
3/2/2011 4:04:17 AM •
Filter Queen...
•
Answered
on Mar 02, 2011
•
3,290 views
How do you reset the
It won't go out by itself.
1. Plug unit into outlet.
2. Press power ON/OFF switch to the ON position.
3. Allow unit to start running at low speed.
4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink.
5. Release both the UP and DOWN arrow buttons.
6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.
1/3/2011 9:37:17 AM •
Filter Queen...
•
Answered
on Jan 03, 2011
•
501 views
Blinking red light above the
1. Plug unit into outlet.
2. Press power ON/OFF switch to the ON position.
3. Allow unit to start running at low speed.
4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink.
5. Release both the UP and DOWN arrow buttons.
6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.
1/3/2011 9:36:03 AM •
Filter Queen...
•
Answered
on Jan 03, 2011
•
592 views
I have a constantly blinking
1. Plug unit into outlet.
2. Press power ON/OFF switch to the ON position.
3. Allow unit to start running at low speed.
4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink.
5. Release both the UP and DOWN arrow buttons.
6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.
1/3/2011 9:35:11 AM •
Filter Queen...
•
Answered
on Jan 03, 2011
•
733 views
How do you turn off the little red filter llight
1. Plug unit into outlet.
2. Press power ON/OFF switch to the ON position.
3. Allow unit to start running at low speed.
4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink.
5. Release both the UP and DOWN arrow buttons.
6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.
1/3/2011 9:33:55 AM •
Filter Queen...
•
Answered
on Jan 03, 2011
•
351 views
Can I just change the
Yes, but keep in mind the warranty requirements:
To receive the full benefit from your Defender ®, replace your filters regularly.
• Every 6 months, replace your Enviropure® Charcoal Filter.
• Once a year (for Perpetual Warranty*)/up to every 3 years (depending on usage),
replace your Medi-Filter® Cartridge.
*Refer to the warranty for information on warranty extension(Perpetual Warranty)
1/3/2011 9:27:42 AM •
Filter Queen...
•
Answered
on Jan 03, 2011
•
190 views
How do you reset the
When the red light is blinking, press and hold both up and down arrows until the red light blinks RAPIDLY, release both for a second or two, and press and hold both again until it stops blinking.
1/3/2011 9:12:56 AM •
Filter Queen...
•
Answered
on Jan 03, 2011
•
1,936 views
Mother gave me her filterqueen defender.. no
The light is a reminder to change the filter, it does not sense if the filter has been changed or not.
When the red light is blinking, press and hold both up and down arrows until the red light blinks RAPIDLY, release both for a second or two, and press and hold both again until it stops blinking.
8/3/2018 10:54:53 PM •
Filter Queen...
•
Answered
on Aug 03, 2018
•
1,447 views
How do I get the top off the Defender to get at
wouldnt have thought their is a manual reset button at all because disconnecting the power would do the same thing .What this seems like is a fault in the circuitry caused by a made in china chip used the programming ,you will be better off throwing it away and buying a new machine which you will do in the end anyway as the control part is sealed in making in the factory
12/23/2010 6:11:23 PM •
Filter Queen...
•
Answered
on Dec 23, 2010
•
59 views
Can i hand wash the carbon blach filter?
No It is a charcoal wrap like the ones used on military chemical warfare suits. it is unwashable once it has been completely dirtied up in the 6-8 month time span
6/30/2010 9:34:09 PM •
Filter Queen...
•
Answered
on Jun 30, 2010
•
443 views
Not finding what you are looking for?