20 Most Recent Samsung HCN4727W 47" Rear Projection Television - Page 8 Questions & Answers

The best plan these days is to buy a 'Board Kit', as it includes all the boards. This is usually the outcome. https://www.fixya.com/support/r29790007-repairing_own_television ..

Hi Bill, the power board in your TV has been extremely reliable and had few failures, it's very simple to test the board, you will see a marking on the board saying 8v standby 13 on, with the set off you should see 8 volts, power it on and you should see 13. See what you see for voltage there and get back to me, if you don't see 13 with the set on it doesn't mean the power board as the main could be the issue, but lets get the 1st test done before digging deeper into it.

Get a factory remote at ebay or amazon for under $10, or use your cell phone, apps can be downloaded for Samsung sets.

Here is a replacement remote for it. All devices like that need a remote. Also break and make the cable HDMI Connections and make sure the television is on the correct source, but you need the television remote for that. https://www.google.com/search?q=Samsung+BD-E5300+replacement+remote& ..

I can't find the model of your set...do you have a typo? Have you tested the backlights with a LED backlight tester to be sure the issue isn't bad strips?

Lets start by eliminating the parts that won't cause your issue, the main board could not cause it, it turns the lamps off, that's correct it turns them off, the inverter will turn the lamps on with the main board not connected. The power board could cause it but it's not probable, only way this could happen would be some shorted windings in the transformer that powers the backlights and in the thousands of?? set's we've repaired in our shop I've only seen excessive backlight voltage a couple times. Considering this set is edge-lite, the lamps get quite warm, if a few are shorted the strip will get hot enough to melt the plexiglass. Where are you getting the replacement lamps from? Is it possible they're not meant for the model set you have? Are you getting a good contact with the tape on the back of the strips? They need to be tight against the frame, is there tape that's bunched up causing a gap between the strips and frame? Without pulling up service lit on the TV (not at shop now) I can't tell you what the correct B+ voltage should be coming out of the inverter but usually it's about 80% of the DC rating of the caps. Other than what I've suggested I can' think of anything else to advise on, I can get the exact voltage of the inverter next week when I get into work.

Under your settings menu on your TV there should be an option for allowing a connection to devices casting to the TV. Ensure your TV is capable of this first. If you provide the model number of the Roshan I can be of more help. After you've verified that your TV is connected to the same Wifi network as your Samsung phone, swipe down from the top of your Samsung, swipe down again to bring up the device controls. Scroll right until you find the icon titled "Smart View". Click on it and it will scan your network for compatible devices to cast your phone to for mirroring or playback. Your Roshan, if configured correctly, should be displayed in this menu.

You have led's that have burned out, and will need to be replaced. Unfortunately, this is a highly frequent problem with Samsungs. The good news - I've repaired a bunch of them. If you can provide me with the model and version number located on the rear of the TV, I can provide you further diagnosis instructions and a link for purchasing replacement LED strips. For your size of TV, the parts should run less than $100.

The most common reasons for the TV to turn on by itself is having foreign matter around the power button of the remote control, external devices connected to the TV, and your settings. If the power button is stuck, clean the remote control.

The screen being green on your TV is either caused by a loose or damaged cable connection of a media component to or from the TV or it could be that the TV's T con board is having problems and it would be more cheaper to bu a new TV than to try and fix the one that you have is broken.

You have internal screen damage from dropping it, you can either watch it this way or buy a new set

I hate giving someone bad news but this model set has a lot of main board issues, there have been many revisions to the original board trying to rectify the issues., you need to match your set to the date code or serial number to get the correct board, the bad news is the main boards can be hard to find and quite costly. A new board should correct the issues you're seeing, we have seen this model with main issues a number of times times in our shop

Remove the back from the TV, unhook the cable going from the power board to main, plug the set in and see if you get backlights, if you don't replace the lamp strips, if you do message me back and I'll get you some other help but I think you will find the lamps don't light up when you power the set up with the connector unhooked!

Chances are you have a stuck button on the button cluster, what I'd do is remove the connector going to it and use the remote control, with a stuck button the remote won't function properly.

https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote

Samsung TV Remote codes for Universal Remotes

directutor.com https://www.directutor.com > content > remote-control... Enter the TV code for Samsung : 0101, and keep trying with Samsung 4 digit and 5 digit remote code list below. The LED light will go off after the correct code ...

• Samsung Remote Control Codes For All Devices

  https://www.directutor.com > content > samsung-remo... Samsung Remote Control Codes for VCR Codes ; 4 Digit Samsung Remote Control Codes = HDTV 0060 0030 0178 0056 ; Samsung Remote Control Codes = TV 1098 1156 1161

Find Remote Control Codes For Samsung TV's

codesforuniversalremotes.com https://codesforuniversalremotes.com > universal-remo... Remote Control Codes For Samsung TVs ; Philips Universal Remote: · 0112 0309 ; 0105 0077 ; 1004 1009 1012 ; Samsung 4 Digit Universal TV Remote Codes: 523 526

What lights?

To program your remote to your Samsung HD 3500, follow these steps:

1. Turn on your Samsung HD 3500 and your TV.
2. Press and hold the "TV" button on your remote until all the mode buttons light up.
3. Enter the three-digit code for your TV using the number buttons on your remote. You can find the codes in the user manual for your remote or online.
4. Press the "#" button on your remote. The mode button you selected should blink twice to confirm the code was entered correctly.
5. Test the remote by pressing the "TV" button and seeing if the TV turns off. If it does not, repeat steps 3-4 with a different code until you find one that works.

If you cannot find a code that works for your TV, you can try the automatic code search method:

1. Turn on your Samsung HD 3500 and your TV.
2. Press and hold the "TV" button on your remote until all the mode buttons light up.
3. Press and release the "Power" button on your remote.
4. Press the "Up" button on your remote repeatedly until the TV turns off. This may take several presses.
5. Press the "#" button on your remote to save the code.

Your remote should now be programmed to your Samsung HD 3500.

Based on the symptoms you described, there could be several possible causes for your Samsung UN65NU8500FXZA not working properly. Here are a few potential explanations: Main board issue: The main board is responsible for processing and sending signals to the TV's components. If the main board is faulty, it could cause the TV to display abnormal behavior, such as not turning on, blinking lights, or no picture. You may want to consider replacing the main board to see if this resolves the issue. Power supply issue: The power supply is responsible for supplying power to the TV's components. If the power supply is not working properly, it could cause the TV to turn off or not turn on at all. You can check the power supply unit for any visible signs of damage, such as bulging capacitors or burnt components. If you find any, you may need to replace the power supply unit. Flex cable issue: The flex cable connects the main board to the other components in the TV. If the flex cable is damaged or not seated properly, it could cause issues with the TV's display. You can check the flex cable for any signs of damage or looseness. If you find any, you may need to replace the flex cable. Backlight issue: The backlight is responsible for illuminating the pixels on the TV's screen. If the backlight is not working properly, it could cause the TV to display a dark or black screen. You can check the backlight for any visible signs of damage, such as dark spots or flickering. If you find any, you may need to replace the backlight. Based on your observations, it seems that there may be a problem with the main board or the flex cable. You may want to try replacing these components to see if it resolves the issue. However, it's always a good idea to consult a professional technician if you're unsure how to proceed or if you're not comfortable working with electronics.