Top 20 Samsung HC-P4241W 42" Rear Projection HDTV-Ready Television Questions & Answers


usually on your model it might be best to replace the entire deflection board as your model has two STK394-250 ICs and then 12 3.9 ohm fusible resistors that will need to be checked and possibly replaced. If you need further assistance let me know I can assist with getting quality parts and circuit boards.

Samsung... | 72 views | 0 helpful votes


Your Convergence output is burnt.DONT turn that TV on until convergence IC's are replaced,orange glowing inside that you see it is resistors that overheating and burning.Unplug TV from outlet before more damage is done

Samsung... | 187 views | 0 helpful votes


Call Samsung for information 1-800-627-4368
What seems to be your problem with TV?

Samsung... | 39 views | 0 helpful votes


send a email to me at [email protected] I have the diagram for that circuit

Samsung... | 46 views | 0 helpful votes


Your Convergence Ic's need repalced. There are 2 of them and they are soldered in.




crikett_27.jpg

Samsung... | 72 views | 0 helpful votes


Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
You can get a repair kit with parts and instructions from www.TvRepairKits.com

Samsung... | 242 views | 0 helpful votes


double vision with the red and green lights .........how do you change them

Samsung... | 129 views | 0 helpful votes


Hi

Thanks for using FixYa.The issue is with the failed convergence (STK) ICs which needs to be replaced. It's not a difficult job if you want to do this yourself, you should require some basic knowledge about soldering-resoldering components. To start with you'll have to open the back of the unit and then replace the ICs (STK ICs) which are located behind the black heat sink and also check the resistors as if they are short the ICs might blow again after sometime.
There are repair kits available which includes repair instructions with the parts, if you want to do it yourself, you can buy and repair it yourself. Please rate the solution if the issue is resolved or post a comment for further assistance.

Thanks
Rylee

Samsung... | 49 views | 0 helpful votes


Convergence ICs need to be replaced.
Go to Encompass Parts Distribution 1-800-638-3328
Type in your Model # for Parts List Just replace the whole convergence board ,if you can solder just order STKs big black ICs will have PN# on them. 1-800-628-1118 and sometimes its Faster,Cheaper in the long run.just to replace the whole board.

Samsung... | 94 views | 0 helpful votes


IF YOU HAVE A DVI CONECTER A BIG WHITE PLUG WITH MANY CONNECTERS YOU CAN BUY A HDMI -DVI ADAPTER BESIDE THE DVI CONNECTER YOU WILL HAVE INDICATION FOR DVI AUDIO YOU MUST PASS TWO AUDIO CABLES FOR SOUND

Samsung... | 233 views | 0 helpful votes


do you smok if yes tack of front panel clean mirror and lense be carful very fragile

Samsung... | 217 views | 0 helpful votes


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony,Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit wiith instructions from the links below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms
  • Screen Looks 3-D
  • Colors wont align
  • Screen may look distorted or warped
  • No Audio/Video - makes a chirping sound.
Problem #2

Another common problem is dull or washed out video.
Your TV2_bing.gif may have one or more of the following symptoms....
  • Dull looking picture
  • White looking picture
  • Halos around objects
  • Red/Orange looking picture

You can see some more examples and find a fix here
bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Samsung... | 186 views | 0 helpful votes


trye on the netz entrance it is a transformer near high capacity capacitator need to make big swamp of parts there transformer,capacitator,som resistors you need to megje it all that area

Samsung... | 141 views | 0 helpful votes


try vancebaldwin.com if you know what board you need, or pts electronics but you need the part #

Samsung... | 76 views | 0 helpful votes


In order to properly provide you with guidance, we need some hint about the problem. Can you describe the symptoms? Is the set dead? Are there any blinking status lights?

Thanks,
Dan

Samsung... | 213 views | 0 helpful votes


To get TV into convergence menu hit mute 183 on remote. If you still cannot get it right you will need to replace the convergence amp IC's.

Samsung... | 690 views | 2 helpful votes


You have a master switch to turn the TV off if not turn the TV on and then pull the AC cable off that will reset the unit then check the remote control setup, let me know if that work if not we go to the next step Please see that grant me your approvals by rating my service and I hope that I can serve you again the future. I will work with you in this issue to conclusion

Samsung... | 132 views | 0 helpful votes


Look to see if any coolant fluid has leaked from any of the CRT's. This is a common cause of multiple component failures in these models. Look real close at the CRT mounting bracket, the wires coming from the CRT's and look at the particle board below to see if you can see any staining or puffed up wood particles. My experience with the Samsung bds is when you have a multiple compoment failure due to fluid leakage it is best to replace the boards instead of component level repair because other components will fail at a later time. Coolant fluid is real hard to spot since it is ultra clear. Hope this helps.

Samsung... | 257 views | 0 helpful votes


You mean red ghosting
easy , replace both cnvergance chip
if you have a repair shop fix it don't pay
more then 175.00 . It's an 1 hour job
and the part cost about 30.00

Samsung... | 243 views | 1 helpful votes

Not finding what you are looking for?
Samsung HC-P4241W 42" Rear Projection HDTV-Ready Television Logo

56 questions posted

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76466 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Demonic-2011
Demonic-2011

Level 3 Expert

513 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Samsung Televison & Video

  • Samsung Televison & Video

Most Popular Question

problems samsung hc p4241w 47 in rear

  • Televison & Video
Loading...