Top 20 Samsung HLR5067WX 50" Rear Projection HDTV Questions & Answers

That is a problem with your main board - some of your inputs work fine and another is bogus. The tv input is not working because there could be a defect in your tuner. If you have cable try a different input for the signal.from the box. If you are using OTA, then use an external HD OTA tuner to feed your set.

Set covergence lines press (mute183) adjust covergence lines

This problem can show up if there is a problem with your HDMI cable. See if problem exists with antenna signal. If it is only on input from HDMI input, change to a new cable.

It means the set is in shutdown and it based on model listed here has a power supply or related problem.

I know this may seem dumb but if you are using component video (the red green blue with the white and red audio cables) it could very well be that the green cable (carries the green signal) is the problem. try changing the configuration (ex: use blue to carry the green signal and vice versa) if the green starts to work and the blue stops then its just your cable.

Two things to look at---------the lamp to see if shattered inside AND with it removed look where it faces at the color wheel--see attached photo.Look to see if any segments are broken, missing etc. Many of the wheels fail in this way and some will have a high pitched or even fan like sound before they fail.Some when really bad will make a grinding noise also. The set monitors the speed of the wheel and if it slows or stops the set will almost instantly turn the lamp off(if possible watch from area where lamp is to see if at turn on to see if it for a moment lights or not.

Remove and inspect the lamp first to make sure it is not shattered--color wheel faces it and can cause this problem also--set monitors the speed and if wheel not running or running too slow it will shut down the set.Look at wheel to make sure it is intact---some of them do come apart and pieces will be missing.

it sounds like you have blown a lamp in your tv.

Sounds like you need to replace your color wheel.

Does the set work with a DVD etc. connected to one of the rear inputs?

If you mean is how to clean the inside dust?..You can used vacuum cleaner and brush to clean or remove the dust..

The analog board is usually at fault when that happens with that model.

That kind of symptoms indicated that the color wheel is already faulty. Confirm where the buzzing sound came from, if it is in front/near the lamp assembly, then you have to replaced the color wheel to resolve the issue.

Tv is on every day and watches 4 to 5 hours every day?Yes,3 years now the projection lamp require replacement again and the board that call the Ballast board might require replacement too,this Ballast board only job is it to ignite the projection lamp only..

those units have had problems with the siganl board and dm module both having solder connection problems and require to be sent out to a rebuilder that can handle that special work you might call samsung consumer and see if its uner and class actions or recalls
other wise it will be a local servicer to assist you further with its problems

This is a clear sign of power source ageing - it's no longer capable of delivering the current needed to start all the components of the tv. Almost surely this is caused by a failure of the capacitors. See this to learn how to spot and replace them
http://www.youtube.com/watch?v=YCSNWi3UHf4
And do not attempt to run the tv until you fix it, or it may fail for good and the parts needed to repair it will cost a lot more than now.

Hello, doesnt sound like much of a problem. Probably a dry joint in the powersupply board. As the tv heats up it cause the components to break contact with the PCB. Its just a matter of resoldering it. Cost? Around $100-$200 should see it out,depending on who you get. I hope I have been of service.

change the thermal sensor located on the light engine section on top of the lamp pn # AA41-00801D

http://www.projectorlampsworld.com/bulb/samsung/hlr5067wx.html


that one there

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.