Samsung HL-P5063W 50" Rear Projection HDTV - Answered Questions & Fixed issues
New lamp, dark picture
It may be time to replace the DLP chip they sometimes have problems like this as well as small white dots all over the screen, lines, etc. There is also a mirror inside the cabinet that may also need to be cleaned. You can also go to SHOPJIMMY.com they have most all of your parts and videos to step you through the entire process of all your tv needs. Check it out Good Luck .
5/3/2017 12:57:12 PM •
Samsung...
•
Answered
on May 03, 2017
•
259 views
Model 5063W - loud noise
The picture is pink, that would point more toward the color wheel, and you can see the fan through the vents in the back and you can go from there. It sounds more like the color wheel since you have a picture malfunction.
2/27/2013 5:39:13 PM •
Samsung...
•
Answered
on Feb 27, 2013
•
303 views
MY TV STARTS EMITTING A BUZZING SOUND AFTER IT'S BEEN ON AN HOUR OR SO. It is a Samsung DLP model HLP5063WX/XAA.
Its likely to be the color wheel which when fails can do several things: A high pitched whine or what is often described as a fan like sound.Since the set monitors the speed of the wheel if it slows down even a little image may look odd or dark.you can at worst hear a grinding sound and it means segments in the wheel are shattered or missingGood news is it is readily available and many average people can replace it---you tube even has video instructions for most of the Samsung models for this.Only two models were made and Google the model number with Color wheel to locate the one your set uses.
12/22/2012 9:05:38 PM •
Samsung...
•
Answered
on Dec 22, 2012
•
98 views
HL-P5063W Constant buzzing when on or off
The clue is you hear it with the set off, most likely a transformer or coil in the standby power supply, not unheard of (no pun) for this type of part to actually vibrate hard enough to make a unpleasant sound that can be heard.Troubleshooting consists of finding (listening) the culprit and either replacing the part or in many cases Hot glue applied (some if a small coil or transformer will use super glue on the copper coils) to the exposed wires on the part.
12/21/2012 3:38:52 PM •
Samsung...
•
Answered
on Dec 21, 2012
•
52 views
No color
I'm not familiar with your set but sounds very much like its the color wheel at fault, if the picture shows perfectly but just lacks color and your set is a DLP with color wheel I'm 99% sure I'm correct.
11/20/2012 1:00:58 AM •
Samsung...
•
Answered
on Nov 20, 2012
•
271 views
HL-P5063W Turns on, but no picture.
remove and inspect the lamp the model indicated uses---you can usually also look from the rear to see if lamp comes on at all---set also prone to bad color wheel--grinding or high pitched fan like sound--it faces the lamp--with lamp removed look to see it is not shattered or missing pieces and that lamp not shattered inside.
typical color wheel
10/22/2012 4:53:45 PM •
Samsung...
•
Answered
on Oct 22, 2012
•
217 views
What causes the dlp chip to start failing
The display chip can fail and will cause pixels out or a burnt image--considering cost is about 200 for the part if you can replace it usually better to replace the light engine.
5/20/2012 7:53:59 PM •
Samsung...
•
Answered
on May 20, 2012
•
66 views
Samsung mirror replacement
Your part# for the mirror is BP67-00096A. Samsung has them new for $198.73 plus shipping. You might be able to find it cheaper if you google it or know someone that has the same model set that does not work.
5/18/2012 2:26:23 PM •
Samsung...
•
Answered
on May 18, 2012
•
52 views
Samsung 50" DLP - Lamp Light Blinking after bulb replacement
Listen closely. The tv should make a high pitch whine as it turns on. If it does wait and see if it tries this a few times. If yes then check the bulb, I have seen cases where the lamp shoves the power connector back into the set. If the tv starts with a grown or heavy vibration noise, then your color wheel may have broken and needs replaced.
5/17/2012 6:32:50 PM •
Samsung...
•
Answered
on May 17, 2012
•
2,369 views
Hlp5063w lamp and temp lights blink and tv doesnt turn on
Look at turn on to see if lamp fires even for a second.If lamp has not been replaced in 2,000 hrs it is a suspect.If you heard a high pitched whine or fan like noise before the set failed remove the lamp and look where it faces----is the color wheel shattered or missing pieces?
4/11/2012 3:41:37 PM •
Samsung...
•
Answered
on Apr 11, 2012
•
92 views
I have a Samsung DLP, model hlp5063w. When I turn
2 most common causes of that sympton would be1. Lamp failure is the most logical culprit BP96-01403a is the lamp number and I recommend only using an OEM replacement2. Color wheel malfunction. Usually when the wheel fails you will hear a very loud motor spinning sound from within the tv. If you havent replaced the bulb in a couple years that would be the most logical cause.
11/2/2011 5:06:18 PM •
Samsung...
•
Answered
on Nov 02, 2011
•
97 views
SljThere is a sound like a motor
Ur tv have a colors wheel design into it.The tv colors wheel it is defective and it is worn out,it is not spinning inside it motor mount axis motor baring anymore.The tv colors wheel is it defective that where the motor noises came from.The tv colors wheel it have to be replace to solve this making motor noises problems.The tv colors wheel it is sit way back of the tv.If u don't have any mechanical skills like take many mechanical parts aparts and putting it back together again.Don't atemp to change the tv colors wheel ur self.Hire a tv tech. to change the tv colors wheel.
9/22/2011 6:45:32 AM •
Samsung...
•
Answered
on Sep 22, 2011
•
113 views
Just replaced color wheel for
You may have to do a reset in service mode....sorry - don't have the guide but it should be in the usermanual for this model.
8/27/2011 2:59:17 AM •
Samsung...
•
Answered
on Aug 27, 2011
•
117 views
Loud humming noise and all pictures are black
Your color projection drives are fried. Usually Red, Green, Blue. Cheaper to replace the set than to replace the drives and have the set re-alligned. Unless you have a TV repair guy in the family or who loves food. :)
8/23/2011 11:48:33 PM •
Samsung...
•
Answered
on Aug 23, 2011
•
56 views
My HL-P5063W won't power on.
Did u ever replace the Ballast board for this tv?No?,that ur tv problems.The Ballast board only job are to ignite the tv projection lamp to make it work.U hearing multiple clicks,lamp never ignite up the Ballast board.
8/22/2011 5:58:27 AM •
Samsung...
•
Answered
on Aug 22, 2011
•
687 views
Not finding what you are looking for?