Top 20 Samsung HLP6163W 61" Rear Projection HDTV-Ready Television Questions & Answers

Could be a bad/failing fan. Is the fan still vibrating? Is it making more noise then normal? Most of the time i find that a fan going bad and vibrating raises heck with the rest of the optics in the TV.

I have a benq projector which has a very noisy color wheel can I stop it or how do I replace it

Hi,The lamp is on the back of the TV. Remove the little door or the back cover to get to the lamp.Here is the link for the video showing you how to remove the lamp.http://www.youtube.com/watch?v=0jr_9A5Xd2QGood luckwww.aaatvservice.com

If using a cable or sat box try a DVD etc when set cold, a box can cause lockup issues via signal.Not a color wheel is correct, more likely a DMD which is rather pricy and almost as much as the entire light engine which comes with it.

Remove and inspect the lamp to see if it shattered inside?

have a expert examine the set to make sure there is no safety issue here and if not the set may have got some plastic so hot that is what you are smelling.

Likely the DMD unit which is part of the light engine--if have to unplug set the microprocessor is getting scrambled and cannot operate. Common and fatal issue as to replace the light engine the cost will exceed the value of this set---DMD can be purchased alone but costs almost as much as the whole engine that comes with it.Seen several of these sets---a shame but even at wholesale the part to fix it makes it not worth fixing.

Some things to be aware of here--if the color wheel turns too slow set will shut down---if you hear a fan like or high pitched sound it is the wheel.If a uniform blue and dark it is likely the DMD which is the box the wheel connects into and can be purchased by itself (forget that as for about 50 more than it costs you can buy the entire light engine that comes with it)Bottom line: Likely a bad or damaged optical light engine.A photo posted here or somewhere else with a URL location might tell me more.further questions? Press the make a comment button on this page.

If color wheel does not run lamp will not fire----with lamp removed have you looked at the wheel----if not running it will cause almost instant shutdown of lamp and the set.If the DMD board is bad time for a new set as it is well over 500 .

If the model number indicated here is correct do not remove the screen---usually all that is required is to remove the back cover (picture is darker and somewhat dull looking?) and locate the three large black lens at top of chassis---they are the light source for this model---clean with a lens cloth or a paper towel with glass cleaner sprayed on it.The set (again based on the model number) may have a mirror in the rear upper part but it rarely requires cleaning.Let me know if questions.

hi,,after the color wheel replacement you need to get the restore sequence procedure using button combination of your remote..try to to this link www.fixya.com/users/chester_pendilton0and get any of my services..thanks

Hello
If there is lamp ON and there is no picture at all, the DLP drive IC on the main board has damaged. Normally, damage to this IC will also couse to DLP [Digital Light Processor] also may get damaged. A thorough check to your Tv is needed. As it is DLP based one, proper care should be taken to repair this set. If DLP drive has damaged, it will be best o repalce the porcessor board as card basis. Anyway, keep in mind that the circuit for this tV is very complicated, such that even an expereinced service technician will also take time to pinpoint the exact fault point. A very high quality multimeter is needed to measure the voltages at the DLP board. Moreover experience is a must to do work with this TV. As far as lamp il ON, there is no fault to its power supply board. The fault lied in the main board itself. If you are aware in electronics, inform me. I'll assist you firther. Otherwise get this TV repaired by any experienced service parsonal or by the authorised service center for Samsung at your town. Authorised service center will have all sophisticated testing equipements ot do this service and it will be perfect in all respect. OK

100% this tv problems it is the tv colors wheel it is defective require replacing.The loud tv buzzing noises sounds are the sounds came from the tv wharp colors wheel it is spinning out control wildly and off of it motor axis and by hitting it to the wall of it steel box holding it.The tv distorted colors pictures are came from out of the reflections of a badly worn out of the tv colors wheel.

This is a fault solution which can be checked and corrected by you assuming that there is no component failure. There is a high possibility that the components over a period of heating and cooling, tend to bring on a problem of dry soldering. So my advice is to check the set for some loose joints that have played on to give you these erratic shut downs or poor performance.

The best way to check for loose connections is to tap lightly when the set is powered on , If there is change while tapping then it seems that there are DRY solder joints. Remove main plug, the covers - with caution of high voltage, check for dry joints, use a good soldering iron to solder all suspected points.

Sometimes the fault occurs when the set warms up, if so you can simulate the heat using a hair dryer on the suspected areas, try with the power supply, distribution, Processor controller, driver controllers on the A/V related sections. Also the use a FREEZE-IT spray can simulate the components to cool and show up the fault.

Based on the above method you must be able to locate the area of fault and solder the sections. Sometimes large IC's- ones with more pins- tend to have drying in some pins and so cause faults related to the IC's protocol. Have a rough idea of looking into the areas to reduce the time of probing.

Check for tips to look into the SMPS unit with some of my tips:

http://www.fixya.com/support/r5826301-working_switch_mode_power_supplies

Thank you for using Fixya.

Replace the color wheel. You can get the color wheel at www.tvrepairworld.com

most likely the color wheel part# BP96-00674A https://www.encompassparts.com/model/SMGHLP6163W/_/_/Samsung/HLP6163W/DLP_TV $126.45 OR http://www.samsungparts.com/Products/Parts_and_Accessories/PID-BP96-00674A.aspx?gclid=CL219fbMksQCFYQ8aQodCqsAtA $135.65 OR http://www.amazon.com/s/?ie=UTF8&keywords=bp96-00674a&tag=googhydr-20&index=aps&hvadid=18887600349&hvpos=1t3&hvexid=&hvnetw=s&hvrand=10445073643222230841&hvpone=&hvptwo=&hvqmt=b&hvdev=c&ref=pd_sl_83y5moj2tm_b various prices

This tv have a colors wheel design in it to this tv.The buzzing noises and the colors are all screwed up because the colors wheel is worn out and spinning off of is axis and rubbing it against the wall of it hall of the steal box frame that hold the colors wheel itself.Don't attemp change the colors wheel by ur self,if u have no mechanical skills.Bacause the colors wheel itself sit way back of the tv,have to take out many mechanicals parts,before can come to the colors wheel itself to replace it.Because u will regret it later if u putting the colors wheel itself in wrong.Hire a tv repair person to replace it.

Replacing the screen on a 61 Inch TV is a serious and expensive process, My suggestion is look for a cheaper TV, possibly a plasma or LCD with HD. They are pretty cheap now and save tons of space compared to the rear projection TVs.

Hi sahazada pak,
As i know, TV set not support sound from PC input.
If you want here sound and still working with PC, you should use HDMI or DVI input from your PC out. HDMI has support image and sound in one cable. DVI only image without sound. if you use DVI , sound pc should connected to audio in.
Good luck.