Top 20
Pioneer DEH-1300 CD Player Questions & Answers
Power but no sound
If your car has an OEM amplified system, make sure the blue (or blue/white if your radio has both) is connected to the blue or blue/white in the after market harness adapter.Also make sure none of the speaker lines are touching metal (grounding out) or touching each other
Hello i recently just got
did you hook the constant power wire up? its the yellow wire coming out of the deck. if this was not hooked up the deck would work fine, but it would not hold the time, or preset stations either
Hello
I have no sound coming
Did you recently install an amplifier along with this system? To me, this sounds like what happens when the amplifier overheats or goes into protect mode. This means that you have two potential problems with your system. Either the amplifier is placed somewhere that causes it to overheat, or your power supply from your car is supplying too much (or too little) voltage. Check to make sure that your amplifier placement is okay, and that you have the correct gauge wire for the power run that you did. For a 13-16 foot run, you should have around 2 gauge wire, depending on how much power your amplifier uses. See this chart for further details http://www.caraudiohelp.com/car_audio_wiring/car_audio_wiring.htm. Beyond those two issues, you could be dealing with loose connections, or issues with the internal electronics. If all else fails, talk to whoever you bought the unit from, and see what they have to say about it. Best of luck!
Error code 11- help-
Error 11 is a disc read error.
1. The disc is not clean or inserted upside down
2. If not the lens is dirty
3. Mechanical error fault. Issue with the mechanics that loads the cd into the spindle motor.
Hope this helps
Positive Feedback ALWAYS Appreciated :)
How do i set the clock
Turn of the unit by holding down the SRC button. Press and hold the Function button, the one to the right of the 6. That should bring up the menu use the arrows to get to the clock.
My pioneer deh-1300 in my
okay have u tryed replacing the wire harness?? sounds like that is the corperate if not you might want to have someone look at your spakers and make sure one of them is not shorting out and causing the protect mode to kick in
How to integrate the pioneer deh-1300mp into a 96
The simplest way to swap the stock radio out for the cassette player would be to go to a radioshack or bestbuy, normally they will carry a double-din to single-din adapter so that the smaller after market radio fits into the existing location snugly. They usually also carry a wiring harness adapter that will plug right into your dodges existing harness and you can just wire nut or solder & shrink wrap the adapter to the pioneers harness, saves a lot of time and insures everything is where it needs to be.
Normally you can get both adapters for under $15, hope this is helps.
The answer above did not work. I have a deh 1300
On my pioneer, you have to shut the unit off, and hold down the source button. If that doesnt work, try holding down each button "one at a time"... Pioneers have run like that for years. You might find some extra equalizers too. Dont go changin too much.
Ok, so I have a 95 nissan maxima se and it has the
Your best bet is to go to a good stereo store that can get you a wiring harness adapter that will plug into your car and be color coded to wire up to your aftermarket radio.
It will save you a lot of time and trouble.
When ever i switch off my engin the radio stations
Hello my name is Israel and I will help you out. You will need to pull out the radio and check your yellow wire connection. You need to make sure that this wire is connected to a constant +12 volt source. Good Luck.
In my car the old
what color are the speaker wires? are they grey and green wires or are the grey green,purple and white?
I hooked all the wires
if you do have all the wires connected right .that mean that your headunit is bad from the manufactured.
Not finding what you are looking for?