20 Most Recent
NetTV PDP42V Television - Page 7 Questions & Answers
My car Ford Territory 2007 iCC unit problem
Unfortunately, if the ICC unit screen has turned white, it is likely that the unit has failed and needs to be replaced. If the car is still under warranty, you may be able to get a new ICC unit from the manufacturer or your local dealer. If not, you can look for a replacement unit online or at an auto parts store.
There is no power to the front panel
If you have replaced the circuit board and there is still no power to the front panel, there could be a few things causing the issue. Here are some things you can try:
- Check the power cord: Make sure the power cord is securely connected to both the TV and the wall outlet. You can also try plugging the TV into a different outlet to see if that solves the issue.
- Check the power supply: If the power cord is connected properly and the TV still isn't receiving power, there may be an issue with the power supply. Check the power supply for any visible damage or loose connections.
- Check the internal fuse: Some TVs have an internal fuse that can blow out, causing a loss of power. Check the owner's manual to see if your TV has an internal fuse, and how to check and replace it if necessary.
- Contact a professional: If none of the above solutions work, there may be a more serious issue with the TV that requires professional repair. Contact a qualified technician or the manufacturer for assistance.
Devant 50DTV700 & 50UHD 202 SERVICE MODE...
To enable the auto power on function on your Devant TV, you can try the following steps:
- Turn on your TV and go to the menu.
- Navigate to the "System" settings.
- Look for the "Power Management" option and select it.
- Look for the "Auto Power On" option and select it.
- Set the "Auto Power On" function to "On".
- Save your changes and exit the menu.
Once you have enabled the "Auto Power On" function, your TV should turn on automatically when it is plugged in after being turned off.
Original password for Phillips dvd player HTS3020/12
There is no specific original password for the Philips DVD player HTS3020/12. However, if you have set a password and forgotten it, you can try resetting the player to its default settings, which will erase any stored password.
To reset the player, follow these steps:
- Turn on the player.
- Press the "Home" button on the remote control.
- Select "Setup" and press "OK."
- Select "Reset" and press "OK."
- Select "OK" to confirm the reset.
After the reset, the player should be restored to its default settings and any previously set password will be erased.
My tv is freezing while frezzing it will turn off the sound and after 3min it will automatically tufe
If your TV is freezing and turning off the sound before turning off completely, it may be experiencing a technical issue that is causing it to malfunction. Here are a few steps you can try to troubleshoot the problem:
- Check the power source: Make sure the TV is properly plugged into a working electrical outlet and that the power cord is securely connected to the TV.
- Restart the TV: Try turning off the TV and unplugging it from the power source for a few minutes before plugging it back in and turning it on again. This can help reset the TV's software and resolve any temporary issues.
- Check for software updates: Some TVs can experience freezing or other issues if the software is outdated or corrupted. Check for any available software updates for your TV model and install them if necessary.
- Check the connections: Ensure that all the cables and connections between the TV and other devices, such as cable boxes or gaming consoles, are secure and not damaged.
- Contact the manufacturer: If none of the above steps resolve the issue, it may be a hardware problem that requires professional repair. Contact the manufacturer or a qualified TV repair technician for assistance.
By following these steps, you may be able to identify and resolve the issue with your TV freezing and turning off the sound before turning off completely.
How to add biss to dansat 991
I'm sorry, but I cannot provide you with a BISS key or any other unauthorized method to access scrambled channels. Using unauthorized methods to view scrambled channels is ******* and can result in legal consequences. It is important to use legitimate methods to access channels and support the broadcast industry.
My Brahn tv started turning itself on and off non stop. All you see on screen is Brahn start up symbol then goes black again
There could be several reasons why your Brahn TV is turning itself on and off and not displaying anything on the screen. Here are some steps you can try to resolve the issue:
- Unplug the TV from the power outlet for a few minutes and then plug it back in. Sometimes, this can reset the TV and resolve the issue.
- Check the power cord and ensure that it is properly connected to the TV and the power outlet. If the cord is loose, it can cause the TV to turn on and off.
- Check the batteries in the remote control. If the batteries are low, it can cause the TV to turn on and off.
- Try using a different HDMI cable to connect the TV to the source device. A faulty HDMI cable can cause issues with the display.
- If the above steps do not resolve the issue, try performing a factory reset of the TV. You can usually find instructions on how to do this in the TV's user manual or on the manufacturer's website.
If none of these steps work, it may be a hardware issue and you may need to contact the manufacturer or a repair technician for further assistance.
Hello am looking into how to put in the code in the urc-01 for sankey ??
The URC-01 is a universal remote control that can be programmed to work with various devices, including your Sankey CLCD-1936 TV. Here are the steps to set up the remote to control your TV:
- Turn on your TV and point the URC-01 remote control towards it.
- Press and hold the "TV" button on the URC-01 remote until the red LED light on the remote stays on.
- Enter the TV code for your Sankey TV. The code for Sankey TVs may vary depending on the model, so consult the manual or the website of the remote manufacturer to find the code for your specific model.
- Once you have entered the code, the LED light on the remote should turn off.
- Press the "Power" button on the URC-01 remote to test whether the TV turns off. If it does, the setup is complete.
If the code you entered does not work, you can try entering another code by repeating the above steps. Alternatively, you can perform an automatic code search by following these steps:
- Turn on your TV and point the URC-01 remote control towards it.
- Press and hold the "TV" button on the URC-01 remote until the red LED light on the remote stays on.
- Press and hold the "Setup" button until the red LED light blinks twice.
- Press the "Power" button on the URC-01 remote.
- Press the "Channel Up" button on the URC-01 remote repeatedly until the TV turns off.
- Once the TV turns off, press the "Setup" button to save the code.
- Test the remote by pressing the "Power" button to turn on the TV.
If you are still having trouble setting up the remote, consult the user manual or contact the manufacturer for assistance.
Every time a cassette is inserted, within 5 seconds the power light blinks, and the cassette does not play, or the system does not play the cassette although the play button is green.
There could be several reasons why a cassette does not play when inserted into a system, and the power light blinks within 5 seconds. Here are some possible causes and solutions:
- Dirty or damaged cassette: The cassette tape itself may be dirty or damaged, preventing it from playing properly. Try cleaning the tape head and the cassette tape itself with a soft, dry cloth or a cassette cleaner. If the cassette is damaged, try playing a different cassette to see if the issue persists.
- Faulty cassette player: The cassette player itself may be faulty. Try inserting a different cassette to see if the issue persists. If other cassettes also do not play, then the cassette player may need to be repaired or replaced.
- Loose connections: Check that all the cables and connections between the cassette player and the amplifier or speakers are properly connected and not loose. If any connections are loose, tighten them and try playing the cassette again.
- Low batteries: If the cassette player is battery-powered, check that the batteries are fully charged or replace them with new ones. Low batteries can cause the power light to blink and prevent the cassette from playing properly.
If none of the above solutions work, then there may be a more serious problem with the cassette player, and it may need to be inspected and repaired by a professional technician.
How can I get out my gld TV stuck in the USB setting
most likely you can press either the 'Menu/Select' or 'Home/Return' buttons located on your remote control to exit the USB setting and return to the main menu. If you do not have a remote control, try unplugging the power cord and waiting for at least ten seconds before plugging it back in. Then use the in-TV controls buttons to try to exit the USB setting and return to the main menu
How do I get out of usb mode without a remote
If you are in USB mode on your device and do not have a remote to exit the mode, you can try the following steps:
- Press the power button on the device to turn it off.
- Unplug the USB device from the device's USB port.
- Wait for a few seconds.
- Plug the device's power cord back into the power outlet and turn the device back on.
If the above steps do not work and the device is still stuck in USB mode, you may need to obtain a remote to exit the mode. Alternatively, you may be able to use a universal remote that is compatible with your device. Check the user manual for your device to determine which remotes are compatible.
What other brand universesal remote can I use on my black point tv
There are many universal remote brands available that you can use with your Black Point TV. Some popular options include:
- RCA Universal Remote
- Logitech Harmony Remote
- GE Universal Remote
- Sony Universal Remote
- Philips Universal Remote
When purchasing a universal remote, be sure to check that it is compatible with your Black Point TV. You may also need to program the remote to work with your TV using a specific code. This code can often be found in the remote's manual or on the manufacturer's website.
Time display in upper left corner isn't working
It would be helpful to know what device you are referring to in order to provide a more accurate answer. Please provide more details about the device with the time display in the upper left corner that is not working.
Why did my cobra camera system stop recording
There could be several reasons why your Cobra camera system stopped recording:
- Storage capacity: If the storage capacity of your camera system is full, it may stop recording. Check if you need to delete some old footage to free up space.
- Power supply: If there was a power interruption or outage, the camera system may stop recording. Ensure that the power supply to your camera system is stable and reliable.
- Camera settings: Check the camera settings to see if there are any settings that have been changed that could have caused the system to stop recording.
- Camera malfunction: It is possible that there is a problem with one of the cameras in your system, causing it to stop recording. Try troubleshooting the cameras individually to see if they are functioning properly.
If your camera system started recording again after stopping, it may have been a temporary glitch. However, if the problem persists, it is recommended that you seek assistance from the manufacturer or a professional technician.
I have a red line down the side of my scanned document using a VuPoint scanner.
You must locate the scanning glass near the scanner opening and open the lid of your VuPoint scanner in order to clean the lens. Above that glass, there ought to be a thin layer of plastic. Remove this plastic carefully, then clean the glass with a cotton swab that has been lightly dipped in cleaning solution or a microfiber cloth. After cleaning the scanning glass, replace the plastic, shut the lid, and attempt scanning once more
Yaesu ft411e lcd not on, when power on ,just flash red led once
It sounds like there may be an issue with the LCD display on your Yaesu FT411E radio. If the display is not working, it may be necessary to replace it in order to restore full functionality to the radio.
You may be able to find a replacement LCD display online through electronics parts suppliers or through radio repair shops that specialize in Yaesu radios. Alternatively, you could try contacting Yaesu directly to see if they have any replacement parts available.
If you are not comfortable with repairing the radio yourself, it may be best to take it to a professional radio repair technician who can diagnose and fix the issue for you.
Mcm298 cd players won't play
If your MCM298 CD player is not playing and keeps saying "changing," there could be several possible causes:
Dirty or damaged CD: If the CD is dirty or scratched, the CD player may not be able to read it. Try cleaning the CD or using a different CD to see if the issue is resolved.
Laser lens issue: If the laser lens in the CD player is dirty or misaligned, it may not be able to read the CD. Try cleaning the laser lens with a CD lens cleaning kit.
Mechanical issue: There may be a mechanical issue with the CD player, such as a worn-out motor or a broken belt, that is preventing the CD from spinning properly. In this case, you may need to have the CD player serviced or replaced.
Firmware issue: It is also possible that there is a firmware issue with the CD player. You can try updating the firmware to see if this resolves the issue.
If none of these solutions work, you may need to contact the manufacturer or a professional repair service for further assistance.
HDTV has horzontal lines and distortion.
Based on the symptoms you described, it sounds like there could be an issue with the LCD panel or the T-Con board in your TV. The horizontal lines and distortion may be caused by a faulty connection between the LCD panel and the T-Con board, or it could be a problem with the T-Con board itself.
You may want to try some troubleshooting steps to see if you can resolve the issue before contacting a technician. First, check that all of the cables connecting your TV to your devices are securely plugged in. If the issue persists, try resetting the TV to its factory settings. If that still doesn't fix the problem, it's likely that there is a hardware issue and you may need to contact a technician for repair or replacement of the faulty component.
Not finding what you are looking for?
