20 Most Recent Hisense 50 Class LED HDTV - 1080p, 1920x 1080, 120Hz, 3x HDMI - LTDN50K360GUS - LTDN50K360GUS - Page 3 Questions & Answers


go into settings and activate computer

Hisense... | Answered on Mar 21, 2020


go into input or source change to port you want

Hisense... | Answered on Mar 11, 2020


you take it to a television engineer.

Here is a question that we see often.
Question:

I've replaced everything in my television because it previously had a black screen with no lighting. Now it doesn't turn on at all and all I have is audio. What could be the cause ?

So your television stops working properly and you think it must be easy to fix, because you can buy boards on eBay, and you can watch YouTube videos. So you make a decision, you buy a board and you fit it, but the television still doesn't work! This is a classic case of the 'let's try replacing this' method of television repair and illustrates why it is a bad idea. It doesn't work for a number of reasons. To correctly diagnose issues, you need to know every board, what is does and every component on the board. You need to know which part has failed, replace the component, or replace the board. The parts you purchased off eBay were probably out of scrapped sets and not tested. The part you put in was dead when you put it in, so you just moved on to another guess at what might be the cause and replace a board that is fine. And so it goes on, you change all the boards and it still doesn't work. Did you notice the large print that says 'No Refunds, NO Returns'. This is to stop you sending your old one back and saying it didn't work, but the unscrupulous use it as an excuse to get money for selling items that may not work! The course to be a television engineer is 2 years full time education, take it to someone that knows how to diagnose and fix. It is by far the cheapest option. The part that failed might be a 20 cents fuse diode hard soldered to a board. They will charge you $2 parts and an hours labour.

Hisense... | Answered on Mar 10, 2020


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. If blinks continue without any pause, the main board is faulty.
Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

Hisense... | Answered on Mar 08, 2020


A hard reset only reinstalls the software. Upgrading the Firmware is the thing that will brick it.

Delete the apps. Turn it off, Pull the mains plug and start reinstalling them.

Hisense... | Answered on Mar 03, 2020


Depends what your 'erro' code is.

Hisense... | Answered on Feb 21, 2020


Do a hard reset to this set, and then check. Its remote control too be faulty. Check it first. Check the remote control for its infra-red emission. Check it with fresh batteries. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician.

Hisense... | Answered on Feb 12, 2020


Main system control IC fault. Contact any service technician. This type of fault can'n be rectified by a user. If you wish to get some details; check the site linked here. Pull up older posts. . http://electronicshelponline.blogspot.com/

Hisense... | Answered on Feb 12, 2020


buttons on side or bottom have to scroll

Hisense... | Answered on Jan 28, 2020


If you did not have this problem before it was moved, the vibration of it being moved may have caused something to come loose. You MUST transport a large flat screen unit like that in a VERTICAL position because the screen will bounce like a trampoline and it breaks. You will have to take the television apart and check all the connections to be sure they are good.

Hisense... | Answered on Jan 24, 2020


You need to check and see if there is a firmware update that might have additional apps. Some televisions dont allow it. You did not post the model number so there is no other information

Hisense... | Answered on Jan 22, 2020


THEN DON'T DO YOU TUBE ON IT SIMPLE SOLUTION

Hisense... | Answered on Jan 20, 2020

Not finding what you are looking for?
Hisense 50 Class LED HDTV - 1080p, 1920x 1080, 120Hz, 3x HDMI - LTDN50K360GUS - LTDN50K360GUS Logo

17 questions posted

Ask a Question

Usually answered in minutes!

Top Hisense Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76376 Answers

Sean Burke
Sean Burke

Level 2 Expert

161 Answers

David Tickner

Level 2 Expert

159 Answers

Are you a Hisense Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hisense Televison & Video

  • Hisense Televison & Video

Most Popular Question

best quality picture

  • Televison & Video
Loading...