20 Most Recent Blaupunkt BLA32/147 32" LED TV 1920x1080, 50 Hz, Freeview, HDTV - Page 2 Questions & Answers

Failed capacitors. Take it in for repair.

go into audio settings and change to variable sound

Sounds like it was half way loading the new firmware and was crashed by the power button. Normally they can take 1/2 hour to finish. The system has now crashed and may have to be reset at the service centre.

There may be several reasons why your Blaupunkt TV/DVD has sound but no picture, but there is typically no reset button that can fix the issue. Here are a few things you can try:

1. Check the cables: Make sure that the cables connecting the TV and DVD player are properly plugged in and not damaged.
2. Check the input: Make sure that you have selected the correct input on the TV for the DVD player. You may need to switch between inputs until you find the right one.
3. Try a different DVD: If the problem only occurs with one particular DVD, then the issue may be with the disc itself. Try playing a different DVD to see if it works.
4. Check the settings: Make sure that the TV settings are configured properly. For example, check the brightness, contrast, and other settings to make sure they are not causing the issue.

If none of these steps work, then the issue may be with the TV or DVD player itself. You may need to contact a professional for further assistance.

If you are only having a "no signal" issue on your Blaupunkt TV, it could be due to several reasons. Here are some possible solutions:

1. Check cables: Ensure the cables between the TV and the device (e.g., cable box, DVD player, etc.) are properly connected.
2. Change Input: Make sure the TV is set to the correct input for the device you are trying to use.
3. Restart Devices: Restart the device and the TV to see if that fixes the issue.
4. Check Source: Check the source device to see if it is working properly.
5. Channel Scan: Perform a channel scan on the TV to make sure it is picking up all available channels.

If none of these solutions work, you may have a hardware issue with the TV or the source device, and you may need to seek repair or replacement.

A blurred screen on the right-hand side of a Blaupunkt TV for about 2 inches from top to bottom can be caused by a few different issues, such as:

1. A problem with the display panel: The display panel may have become damaged or malfunctioned, causing the blur on the right-hand side of the screen.
2. A problem with the T-CON board: The T-CON board controls the video signal between the main board and the display panel. If it is not working properly, it can cause the blur on the right-hand side of the screen.
3. A problem with the main board: The main board controls the various functions of the TV. If it is not working properly, it can cause the blur on the right-hand side of the screen.
4. A problem with the cable or connector: Damaged or loose cable or connector can cause the blur on the right-hand side of the screen.

It's best to consult the manual or a professional technician for help. They will be able to diagnose the problem and recommend the appropriate course of action. Sometimes, the problem can be solved by replacing a faulty module, repairing or replacing damaged cable or connector, but in some cases the repair may be more complex and require more extensive work.

https://www.pcmag.com/how-to/stop-tv-from-turning-on-off

You have changed the battery but it still not working means now you should replace it. I think this is last option.

Hi, please start with a basic power cycle. If this does not work, please put your picture settings back at their default. If still having issues, please perform a factory reset. Thank you.

Hold down the menu button on the top or side of your TV for at least 10-15 seconds. An on screen menu will appear asking you to enter the time, date and location settings. Follow the onscreen instructions, and once completed your TV will reset to factory settings.

Yes kambria is a scammer. BEWARE!!!

Horizontal lines are almost always caused by a bad panel and not fixable.

Start by getting some voltage readings on the power supply, are you getting the command from the main to enable PWM on the power board? If so do your power supply voltages look normal? If not, replace the power supply if they look ok look at main board issues, also be sure all connectors are seated correctly

Have a read of this Tip I wrote. https://www.fixya.com/support/r29790007-repairing_own_television ..

Does it take them in and then spit them back out? Buy a CD Optics Cleaning Disc. It has small brushes to clean the optics. If the low power tracking optic can't see the tracks, it rejects the disc.

if tv model number is BP650USG9700Q then follow these instructions either right click - save link as or click on it https://www.appliancesonline.com.au/public/manuals/BP650USG9700Q-User-Manual.pdf go to page 14 of user manual and it explains how to open remote

You don't give a model number, so let's just guess :>0 Page 12 of _this_ manual https://www.blaupunkt.com/uploads/tx_ddfproductsbp/BP3200AU6000%20-%20Instruction%20Manual%20v12.pdf ..

I would order the correct remote control for it and send the other one back as it doesn't work properly.

check the link below https://www.google.com/search?q=4+digit+code+list+ucr-501a+sansai+remote+for+a+tv+blaupunkt&oq=4+digit+code+list+ucr-501a+sansai+remote+for+a+tv+blaupunkt&aqs=chrome..69i57&sourceid=chrome&ie=UTF-8

Time for new at walmart. This time buy a fan to keep it cool. Tv will fail from heat earlier