20 Most Recent HEWLETT-PACKARD Envy 5530 built-in WiFi HP Thermal Inkjet eAll-in-One Color Printer - Page 7 Questions & Answers


Kala Mistral error 19 is an encoder (motor’s internal hall sensor) error

Office Equipment... | Answered on Sep 09, 2020


Good morning sir please when I print out any copy it print double and I have change chip what should be the promble

Office Equipment... | Answered on Sep 07, 2020


photo paper is normally thicker that normal paper used in printers . try adjusting paper thickness settings to thicker paper or heavier gram weight paper

Office Equipment... | Answered on Sep 04, 2020


When you get the error message "Replace imaging unit, 0 estimated pgs remain [84.3x]" This means the imaging unit has reached end of life and needs to be replaced. The device will not print, and this message will not be cleared, unless you replace it with part number 50F0Z00
(or 500z)
Vertical streaking. If the imaging unit is near end of life, or the device has had problems with non standard toner, vertical streaks may occur on the page. Replacing the imaging unit will resolve the problem.
Vertical streaks on page
Vertical band at top of page. This typically appears on printed images, but can also appear on text. The most likely cause is toner contamination on the charge roll, however if the band is still visible after printing 30-40 continuous pages this means the imaging unit needs to be replaced.
Vertical Banding on images
Seal failure on the imaging unit. Occasionally seal leaks have been seen from the Imaging Unit.
Toner will be seen on the main frame near the Imaging Unit sides.
If toner build up is excessive, it may even fall into the Tray below. Cleanup with a toner vacuum may be needed.
Replace the Imaging Unit to fix the problem.
Spots, scratches, marks on the page. If they are random, this indicates a problem with toner scatter.If they are repeating patterns, measure the distance between matching marks or spots. If the distance is one of 97mm, 47mm or 38mm, this indicates marks or dents on the imaging unit and it will need to be replaced.
You receive the message Replace defective imaging unit The imaging unit is defective and needs to be replaced. If you just installed it, it will be covered under warranty - contact Lexmark Australia on 1300 362 192
You receive the message Reinstall missing or unresponsive imaging unit and the below instructions don't resolve the problem. Try one or more of the following:
  • Check if the imaging unit is missing. If missing, install the imaging unit.For information on installing the imaging unit, see the "Replacing supplies" section of your device's User's Guide
  • If the imaging unit is installed, then remove the unresponsive imaging unit, and then reinstall it.
  • Note: If the message appears after reinstalling the supply, then the imaging unit is defective. Replace the imaging unit.
You receive the message Replace unsupported imaging unit The imaging unit you attempted to install was either non-genuine, or was from a different region. Buy a genuine Lexmark imaging unit from an authorised Lexmark supplier in your country/region.
You receive a 31.6x error One of the following errors is shown on the display:
31.60 Imaging unit smart chip error
31.61 Imaging unit I2C packet timeout
31.62 Imaging unit I2C packet has been sent but code timed-out on receiving the data (callback)
31.63 Imaging unit security error in the send challenge sequence
31.64 Imaging unit ROM signature error
31.65 Imaging unit stuck busy (status register and/or CRI Arbiter register report busy)
31.66 Toner failed to replenish into the imaging unit
In this case you need to ensure that the imaging unit is properly installed. If yes, check if the imaging unit is supported. Replace with a supported imaging unit if necessary.
If the problem remains, you will need to organise a Lexmark service call (Australia 1300 362 192)
You receive error message 32.11 Imaging unit smart chip compatibility error This could be caused by an unsupported imaging unit (non-genuine or incorrect region). Replace with correct imaging unit to clear this error. If your imaging unit is supported, you will need to organise a Lexmark service call (Australia 1300 362 192).
You receive error message 84 Imaging unit low If expected, replace the imaging unit. If unexpected, call Lexmark Support (Australia 1300 362 192)
Replacing the imaging unit

Office Equipment... | Answered on Sep 01, 2020


If error code F135 appears on your oven. It indicates that the oven door cannot close because the pyrolytic function is on. Check if the top part of the door is intact and secured properly to the door

Office Equipment... | Answered on Aug 28, 2020


5-2 THREADING the LAMINATOR
1. Remove the supply roll mandrels and the feed tray. The supply roll mandrels are now ready to accept
loading of the film rolls, wound with the polyester (shiny) side out. When viewed from the front of the
machine, the core grippers on both the top and bottom supply roll mandrels should point toward the
heat shoes (and toward each other). The tension control knobs should be positioned on the right. Notice the
knobs are labeled "Top Right" and "Bottom Right". If you have rolls of film on which the material is wound
in the opposite direction (adhesive or dull side out) exchange the top and bottom supply roll mandrels so
the core gripper positions are reversed.
2. Slide a roll of film onto the top supply roll mandrel, turning the roll slightly to slide the gripper inside the
core. Center the roll. Make sure the dull side of the film is facing up and the shiny side is facing the
heat shoes during the threading. Scored marks on the supply roll mandrels provide a guide for proper
alignment of the two rolls of film to each other.
NOTE: The pointed metal pieces protruding from the body of the supply roll mandrels grip the cardboard core of the film supply roll to prevent slippage. When placing a roll of film on the mandrel, twist the film supply roll to
accommodate easier film loading.
3. With the roll aligned with the scored line on the right side of the mandrel, place it in the top bracket.
Place the left side of the shaft in its slot first then place the right side of the shaft in its slot, turning it as
needed. FOLLOW THE RECOMMENDED LOADING PROCEDURES CAREFULLY WHEN THREADING
FILM IN THE LAMINATOR. ACCURATE ALIGNMENT OF ROLLS WILL MINIMIZE WASTE AND HELP KEEP
THE LAMINATOR CLEAN.
4. While the machine is still cold, review the threading diagram. With the bottom roll of film centered on
the mandrel and the shiny side facing down, run the film under the bottom idler bar and pull towards
you.
5. Load and thread the top roll of film in the same manner as the bottom roll. Refer to the threading diagram. The
film should run under the silver stabilizer bar and over the front of the top heat shoe. Remember, the shiny
side of the film must always go against the shoe. The dull (adhesive) side must face away from the shoe.
Make sure the two rolls are aligned with each other before going to the next step.
6. Turn machine on and heat to the desired temperature.
7. With both rolls threaded and installed in their respective brackets, unwind enough film from the top roll
to reach the bottom of the bottom heat shoe. Next, unwind enough film from the bottom roll to reach the
top of the top heat shoe.
8. Now drape the film from the bottom roll against the film from the top roll on the top shoe. If the laminator is
hot, the exposed adhesive on the top web will hold the bottom web and make it easy to stick the two rolls
together. If you are threading the machine while it is cold, use tape to stick the bottom web against the top
web.
9. Tip the safety shield down into the laminating position. With the film draped over the two heat shoes, push
one edge of the threading card between the heat shoes so that the film is firmly positioned against the
laminating rollers. If a threading card is not available, any piece of card stock or poster board will work.
10. Make sure there is still enough slack in the web. Turn the drive switch to FORWARD, permitting the film and
feed board to pass through both sets of rubber rollers. Carefully monitor initial threading to be sure the web
reaches and passes through the pull (back) rollers. When the threading card has cleared the back of the
machine, move the drive switch to the center position (off). Whenever you want to remove the film and/or
laminated material from the back of the machine, use the zippy cutting tool provided with the laminator.
11. Slide the feed tray into position.
12. If the machine has the slitter option, make sure the slitters are disengaged (blades in the raise
position) and moved all the way to either side of the machine.
CAUTION: The laminator is designed to be run with the operator directly facing the
control panel and feed tray, not at an angle or from the side of the machine. For
operator safety, the safety shield must be in position over the upper heat shoe
when the machine is ON, or when the drive switch is in the forward position.

Office Equipment... | Answered on Aug 25, 2020


I need to replace the rollers on my IBICO 2700 laminator. I will need to order the new rollers can you help?

Office Equipment... | Answered on Aug 25, 2020


I need a new cord. Also, the machine does not get hot enough to melt the holes.

Office Equipment... | Answered on Aug 25, 2020


You may have installed a software wrong... or installation was aborted, interrupted, etc. You will need to hire a technician to fix it for you.

Office Equipment... | Answered on Aug 22, 2020


My Toyota Hybrid Prius NSCP-W62 CD Player and Navigation system get a error message E00000A once I inserted the memory card and switched on the vehicle.
Somebody help me to correct the error and get the menu.

Office Equipment... | Answered on Aug 20, 2020


https://www.youtube.com/watch?v=mvgWn4pAKmM


https://www.youtube.com/watch?v=jKAxfHcDumY


Youtube videos showing ways to clean printhead in Epson L printers.

Office Equipment... | Answered on Aug 14, 2020


Hellos Ashfaq
Please advise what solution you did against this Error Code

Office Equipment... | Answered on Aug 10, 2020


Hi,
Hp are tricky scanners to install and setup. You need to unplug the USB cable, power on the scanner and begin a fresh setup.

Let the software tell you when to reconnect the USB cable to the computer. Let it finish setup and reboot computer. Once in windows, the setup will complete automatically.

Go in START menu and click on the HP Solution Center in the HP folder to activate the scanner.You can't jsut press the SCAN button on the scanner. It won't work. You need to start the software first or use Photoshop.

Also, the way to fix this Error 20 is to first ensure that your HP Printer is set up to be the default printer on your PC. It's often the case that the printer you have on your system will either not be the default, or will have some sort of error that will prevent it from being properly used. You should click onto "Printers & Faxes" on your system and then right click onto your HP Printer, and select "Set As Default". This will allow your PC to use the printer every time you print,removing some confusion.
More Help... HP LaserJet Error Codes and HP Printer Support

Thanks,

Office Equipment... | Answered on Aug 07, 2020


Panasonic kx-ft981 ,dark print out and copy.

Office Equipment... | Answered on Jul 25, 2020


Canon Printer Error B200 means a faulty print head. A print head is a part that divides the ink from the cartridges on the paper, indicating it's one of the several important features of the entire printer. Print heads are known to be problematic, particularly on cheaper printers.

6 steps to Fix Canon Printer Error B200:-

1. Reset the printer.
2. Remove any obstructions.
3. Clean the printer head.
4. Manually clean the print head.
5. Remove old ink.
6. Re-install the printer drivers.

For Expert Advice check here- Canon Printer Error B200

0_rwlma5mq2bbnwyse-undefined-undefined-0_25.jpg

Office Equipment... | Answered on Jul 25, 2020


Hello im using the ROHS mt871, and also have the Easy Cut Studio... Do i have to intall a driver first? or just by using "generic Plotter" i can cut? thank you so much

Office Equipment... | Answered on Jul 17, 2020


Please error tds 450 10504-271

12a6fdd4-3fbd-4644-a9c9-c1bd5730d006.jpeg

Office Equipment... | Answered on Jul 08, 2020


It'a problem with main motor encoder feedback. Usually problem with wires

Office Equipment... | Answered on Jul 08, 2020


Have you tried a Google search or Duckduckgo search for Dwf 7108? If so, you likely have discovered the device can not be found without other identifying information. If I assume it is a printer and not an office washing machine from DaeWoo, I find myself routed to AutoDesk forums. The point is, you need to identify the Brand and Model and type of hardware you are enquiring about, as well as error codes (which are typically specific to brand). Sorry. You might do a Google search for the brand named object and model number plus error codes or go to the manufacturer's site for support. I can't identify the hardware you are referring to.

Office Equipment... | Answered on Jul 07, 2020

Not finding what you are looking for?
HEWLETT-PACKARD Envy 5530 built-in WiFi HP Thermal Inkjet eAll-in-One Color Printer Logo

7 questions posted

Ask a Question

Usually answered in minutes!

Top HEWLETT-PACKARD Office Equipment & Supplies Experts

Harrie

Level 3 Expert

6746 Answers

Duke Bells

Level 2 Expert

131 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Are you a HEWLETT-PACKARD Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

InkJet HEWLETT-PACKARD

  • InkJet HEWLETT-PACKARD

Most Popular Question

double side printon hp5530 when default

  • Office Equipment & Supplies
Loading...