20 Most Recent Panasonic Workio DP-150PA Copier Questions & Answers

Hello :

polygon motor synchronization error. possible causes are :

1: engine pcb
2:laser unit
3: lvps
4: sc pcb

reseat all the connectors before starting to replace boards

please rate !

You change to the defult setting of your copier sold be set on fax. Try this link and download the operating manual. hopefully this will help you.
http://panasonic.net/pcc/support/mfp/

There is not supposd to be any E1-02,...THERE IS an E1-20, it is saying you have a prob in your "optics" unit, possibly even the Lser unit...you should probably have a service man determine exact prob.

xenon lamp is disconnected

there are metal strips on the 4 corners under covers and behind cassette front panels that need to be taken off. beware of any connectors at back when taking apart.

You might be able to download a manual here:
http://www.retrevo.com/s/Panasonic-DP-150-Copiers-review-manual/

I'm not sure that model supports emailing scans. I couldn't find it in the manual. Just setting up the fax phone book on page 139.

The drum (green roller) is causing your problem. If it has toner on it, cleaning it will not help...it may make it worse. The unit has a cleaning station built into it, and when it fails the drum unit needs to be replaced.

Google "PANASONIC DP-1520 PRINT DRIVERS" or go to:
http://www.panasonic.com.au/support/downloads/file_type_results.cfm?fileTypeID=1&productCategoryID=28&productID=387
It's Panasonic Australia, but its the same ones I use. Use the GDI print driver to avoid any problems. Make sure you get the right one for your OS (ie WIndows XP, etc)

"p" I believe on this model means its out of paper. Need more info!

What problem? Need more info! On the Panasonic brand, you input the IP address through the "function" mode- "general" settings... go to last menu item "key operator" the code should be 3 or 4 zeros. Then go to the IP address item and enetr in the IP adress. Now you MUST TURN THE MACHINE OFF AND BACK ON TO LOCK IN THE IP ADDRESS! Go back into general setting and "print general settings" to see if it's still the same address.

just check all sensors in paper path .j87 shows inverter problem.MIAN AKHLAQ

the fuser unit has ceased to heat...it has a bad heater. the fuser is a hollow metal roller that usually has a powerful light inside to heat the metal. a continuity test can detect

you may try this:
unplug the network, usb, and fax connection
remove all papers
turn on the machine
press print key
press stop
press 1 for yes to cancel the job (if theres a job queue)

Yeah, I just mean taking it in and out to be sure you have good connections.
Sorry for the delay, I couldn't find this responce for anything.
My blackberry screwed up and deleted my browser and the e-mail I received.

Have you reseated the drum and toner?
It can be a drum cartridge problem. have you tried that?
You say copy or print, so I am asuming this is multifunction and you do both printing and copying.
1, Have you shook up the toner cartridge well.
After the drum and shaking the toner, I would suspect the transfer assembly, Off hand I cant remember of that machine has a transfer roller, or if there is a channel where there is a hair fine wire running through it.
The wire may have broken, or if its a roller making poor contact.
The laser is also possible.The transfer will be on the right had door assembly.
Take the cartridges out and see if there is anything laying loose in the machine,
what you are describing sounds more like a drum or transfer problem.
sounds very much like a defective transfer. And again, could easily be the drum.
Did you have a jam just before this occured? If you had a jam in particular in the right hand door, you broke the transfer wire.
Yeah, i am rambling huh?

there is high voltage or corona probleb in your copier contact any technical person

That is a laser unit error. If resetting the machine's power doesn't clear it up, then it means the laser unit is dead/dying. If that's the case, your only choice is to replace the laser unit.