Aiwa Z-HT65 Shelf System - Page 6 - Answered Questions & Fixed issues
I need the codes for a aiwa stereo
Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.....
http://electro-medical.blogspot.com/
6/10/2016 5:55:17 PM •
Aiwa Audio...
•
Answered
on Jun 10, 2016
•
215 views
What power source to be used id I am using AIWA PX-E55 as a stand alone unit?
You could probably run it off a large 9 volt battery, as long it doesn't run off a 6 volt supply. How much control of the speed depends on if the deck has inbuilt speed pre-sets to adjust it. In fact that is crucial for any power source that you use. As it will either be too high or low to run the turntable at the correct speed. So if there are no pre-sets on it you will have build that in to the power supply. It all depends on if the original power supply in the unit it was attached to had it controlled from there.
I would have a look at the motor in the deck, it might tell you what it runs on.
Once you find the voltage the motor runs off, you can narrow a suitable power supply down. For example if it ran off a 12 volt supply, you could use a model train set transformer. As basically the motor is nearly the same as train set motor! But must run off about 9 volts that I have seen.
5/17/2016 7:54:43 PM •
Aiwa Audio...
•
Answered
on May 17, 2016
•
463 views
My Compact Disc Stereo System NSX-AJ50 is tripping
One or more of the output transistors has failed or you have a bad speaker. Try disconnecting both speakers and turning on the unit. If it still shuts down, then the transistors are likely to be defective. These can be replaced for about $15-$25 plus labor at any service shop that handles audio gear.
Dan
1/21/2016 8:48:16 AM •
Aiwa Audio...
•
Answered
on Jan 21, 2016
•
312 views
How do i set the time on the aiwa cx-naj22
If you don't have the remote, go to CD mode and power off. Push the "pause" button, when the blinking clock appears, quickly press the "pause" button again. Use the back and forward buttons to set the time.
1/9/2016 4:13:02 AM •
Aiwa Audio...
•
Answered
on Jan 09, 2016
•
294 views
Hi: I have a aiwa nsx 800 mkII I hear left channel normal but the right channel sound very low ?qhere can I fix that?
Check first it is on all functions. If it is then it will be a power amp fault. As the unit has two channels both of which are identical to each other it's possible to check and compare each channel. So in your case the left hand channel parts are your guide to what is right. Compare first visually the two channels. If something looks burnt or damaged or wrong in the right, but it isn't in the left then you will have found the cause.
If everything looks OK, then carry out voltage tests, if you have a meter. Or a sound test. This involves touching with an insulated screwdriver the two channels while the unit is on. Never touch any part that there is only one of. Unless it's an IC and has two channels going in it. You will hear a buzz if it is working or produces sound. Again a good buzz in the left should happen in the same place as the right. When it's load at one point of a part but weak on the other, when it should be a loud buzz then you have found the faulty part.
Please however check first that it's not the headphone socket that is causing the problem. Sometimes the sound will be OK on headphones but not on the speakers. The socket the headphones fit into can cause this.
11/9/2015 4:50:07 PM •
Aiwa Audio...
•
Answered
on Nov 09, 2015
•
319 views
AIWA CX NA202 DOES NOT PLAY CD
The reader is probably shot. You can replace it but you will have to take it apart to get a part number for searching.
9/23/2015 6:41:21 PM •
Aiwa Audio...
•
Answered
on Sep 23, 2015
•
194 views
Aiwa crt tv as2180nh stand by red led is on but no display
9VDC supply come from one of the LOT winding. If it should be there, the LOT should work. Check and replace damaged component/s at its horizontal scan output section circuit. Check the LOT (Line Output Transformer) too for damage. Replace the horizontal scan output transistor. Check the input voltage to LOT. If the voltage is absent check the feeder resistor; if any. If you wish to get some details; check the site linked here. Surf the site with patience.
Pull up older posts.
http://electronicshelponline.blogspot.com/
7/23/2015 8:14:04 AM •
Aiwa Audio...
•
Answered
on Jul 23, 2015
•
185 views
Not finding what you are looking for?