Alpine CDA-9811 CD Player - Answered Questions & Fixed issues

Make sure you are using the blue/white wire to turn your amp on. The blue wire is antenna remote turn on and turns off when leaving tuner mode. The blue/white wire is amplifier remote turn on.

Did you check both the red and yellow wires? You may have a bad connection elsewhere in the vehicle or even bad solder connections inside of the radio itself.

try pacparts.com.

push and hold the menu and center button for ten seconds to REFRESH your ipod OR it 's the menu and play button.

No, its ok. Try to check the wire connection in the power supply. Check the fuse if the spring that pushes to contact is still working. The problem is on that area.

you probably have a bad output ic inside the deck.

I would try using a lens cleaner to clean the CD player.

this specific model alpine was famous for that pull the radio out and check the red yellow and black wire were they go into the harness on the back of the radio sometimes the pins in the harness loosen up

i have seen the adaptors for most any radio on ebay for that

go to the alpine help forum and state your query theyl help you no bother, youl find this forum if you google apline car audio

Press "Title" until time is displayed. Then press and hold "Title" for a few seconds until time is displayed. Turn the silver knob to change the hour, after hour is set, press the silver knob to activate minutes. Turn sliver knob to change minutes. Press silver knob to end.

YOU NEED AUDIO INPUT SO IPOD CAN WORK

you will need an ai-net cable. your local car audio dealer will definitely know.

you will need to set up your system to accept aux. default setting is 'aux off'. refer to system manual to setup system to accept 'aux on' on pages 23 & 24. please read carefully as instructions are confusing.

you need to set up your system to accept aux. this means you will need to set the 'aux on', as the default setting is 'off'. use the manual and refer to page 23 & 24. please read the instructions carefully, as they are slightly confusing.

The signal should go from the head unit to the amp to the subs. Someone must not have wired the subs correctly through the amp, or amp to the cd player..

Are you sure you are using the audio input wires and not the audio output wires on the back of this radio. there is also an input switch you need to set before the Ipod will work

1. Mechanical Issue: There might be a mechanical problem with the disc drive or the eject mechanism. It's possible that a part is jammed or not functioning correctly.
2. Dirty or Damaged Disc: If the disc is dirty, scratched, or damaged, the player may have difficulty reading it and thus not ejecting it properly.
3. System Error: There could be an internal error within the player's software or firmware causing it to not recognize the disc properly or to malfunction when attempting to eject it.
4. Power Issue: Sometimes, power-related issues can affect the functionality of electronic devices. Ensure that the player is receiving adequate power and there are no loose connections.

Here are some troubleshooting steps you can try:

• Turn off the player and then turn it back on to see if it resolves the issue.
• Try ejecting the disc using the manual eject button (if available). This button is usually a small pinhole near the disc slot. You can insert a paperclip or a similarly sized object into the hole to manually eject the disc.
• If possible, try using a different disc to see if the problem persists. If other discs work fine, then the issue may be with the original disc.
• Check for any visible obstructions around the disc slot and remove them if present.
• If none of the above steps work, you may need to contact Alpine customer support for further assistance or consider taking the player to a qualified technician for repair.

Se o Bluetooth do seu Alpine CDE-W235BT parou de funcionar ap?s uma falha durante a atualiza??o, pode haver algumas etapas que voc? pode tentar para resolver o problema: 1. **Reinicie o Aparelho:** - Desligue o r?dio por alguns minutos e ligue-o novamente. Isso pode reiniciar o sistema e resolver problemas temporariamente. 2. **Restaurar as configura??es de f?brica:** - Consulte o manual do usu?rio para descobrir como realizar uma restaura??o das configura??es de f?brica em seu Alpine CDE-W235BT. Isso pode resolver problemas causados por configura??es incorretas. 3. **Verifique a vers?o do firmware:** - Se poss?vel, verifique a vers?o do firmware do seu Alpine CDE-W235BT. Se houver uma vers?o mais recente dispon?vel, considere atualizar novamente o firmware, seguindo rigorosamente as instru??es do fabricante. 4. **Remova Dispositivos Pareados:** - No menu Bluetooth do r?dio, remova todos os dispositivos pareados anteriormente e, em seguida, tente parar novamente. ?s vezes, problemas de conectividade podem ser resolvidos removendo e pareando novamente os dispositivos. 5. **Atualiza??es de Software:** - Verifique se h? atualiza??es de software dispon?veis para o seu Alpine CDE-W235BT no site do fabricante. Caso existam, siga atentamente as instru??es para realizar a atualiza??o. 6. **Contate o Suporte T?cnico:** - Se as solu??es acima n?o resolverem o problema, entre em contato com o suporte t?cnico da Alpine. Eles podem fornecer assist?ncia espec?fica para o seu modelo e orienta??es adicionais para resolver o problema. Lembre-se de que mexer no firmware e nas configura??es do dispositivo envolve riscos, e ? sempre recomend?vel seguir as instru??es fornecidas pelo fabricante para evitar danos permanentes ao aparelho. Se voc? n?o se sente confort?vel fazendo isso por conta pr?pria, procurar ajuda profissional pode ser uma op??o.

Question edited for clarity. https://www.google.com/search?q=alpine+vie-x077+wiring+diagram https://www.google.com/search?q=alpine+vie-x077+installation+manual ..