Hino 2006 268 - Answered Questions & Fixed issues


The clutch plate is probably stuck. If you have a clear space in front of the truck select first gear, release the parking brake and start the engine with your foot on the clutch. The vehicle will lerch forward and the engine should start with the vehicle now moving forward. Hit the brakes with your left foot still on the clutch and the clutch will probably release and work normally.

Hino 2006 268 | Answered on Jan 15, 2019 | 239 views


that could be dependent on the engine. BUT, since you didn't tell anyone, it is impossible to give you a concise answer. anyway, once you decide what engine, look it up yourself on the internet rather than take someone's word for it.
setting that clearance adjustment could be really important for engine life.

Hino 2006 268 | Answered on Oct 19, 2018 | 567 views


Hiya,

When your painting iron its all about the primer, this helps its withstand the elements. Make sure you
also remove any existing rust! Here is a good example of how to paint a iron fence. Let me know if you have any questions


imgbin_fence-gate-wrought-iron-steel-png_yt244huw-undefined-undefined-0.png

Home Fencing | Answered on Aug 25, 2020 | 113 views


The timing relay has to be setted right.
There is a time control on every unit,.
1-[Distance has to be set right before setting time relay]
2-(opening time and closing time has to be set accordingly to ur safety and wanting)

Home Fencing | Answered on Mar 27, 2019 | 946 views


Do you have sensors that stop the gate closing on people or cars ? If so put your ear near the sensor but not inline with the opposite one. Now gently wave your hand in front of it .... if there is no click then something is obstructing the beam. Sometimes spiders get inside and spin that candy floss type web in there .

Home Fencing | Answered on Mar 18, 2019 | 1,411 views


The first place to look is your receiver. This is the device, often separate from the actual gate operator, that responds to your transmitter. Stand next to the gate operator and you should hear a small click coming from the receiver when you or someone else pushes the button.

You can sometimes find the receiver by following the antenna cable back to it. If it does not have an external antenna, look inside the operator box for either an antenna screwed into the receiver or a wire hanging from a plastic box.

If you hear the click and the gate does not open, the possibilities grow exponentially so we won't try to address every possibility here. If you hear a click when you are close, but not when the transmitter is triggered at a distance, check the antenna.

If you don't hear the click, then either the remote has lost programming (this often happens with rolling codes transmitters when they are not used for a long time), or the receiver is not working.

Check to make sure the receiver is getting plenty of power power using a meter. It should read at the recommended voltage or a bit higher. Usually around 24 volts but some receivers can work down to 12 volts. If it gets plenty of power and the remotes have been programmed back in, consider replacing the receiver.

Home Fencing | Answered on Mar 08, 2019 | 440 views


remington model 476 power nailer

Home Fencing | Answered on Oct 19, 2018 | 1,205 views


indirectly we can help. and if you were to bother checking with the manufacturer, you could easily get the right answer.

Home Fencing | Answered on Oct 19, 2018 | 699 views


you can find one via the internet. doh.

Home Fencing | Answered on Oct 19, 2018 | 355 views


duct tape.

Home Fencing | Answered on Oct 19, 2018 | 466 views


what about them ?

Home Fencing | Answered on Oct 19, 2018 | 316 views


I think you should hire a competent electrician. your question indicates you aren't qualified or competent to work on electric power, and it could cause a fire.

Home Fencing | Answered on Oct 19, 2018 | 605 views


look it up on the internet and get the right answer, complete and fully described.

Home Fencing | Answered on Oct 19, 2018 | 648 views


High energy bills is a very common problem. Every home owner or tenant wish to save energy to lower energy home energy bills. There are different ways to lower your home energy bills. I am going to share a blog post which will guide you to do it properly.

Home Fencing | Answered on Oct 19, 2018 | 491 views


Check for obvious bad contacts. The next thing to check is the loop detector itself. Since you are checking inductance measured in Henry's it would be good to get the specs from manufacturer Try calling customer service.

Home Fencing | Answered on Mar 18, 2018 | 381 views


If you dont already have this: try adding sod, some mulch and afew plants (with colors). But keep in mind it should have low maintenance. Alot of homebuyers like low maintenance. Something that they can do themselves or hire someone to do cheap. Please see below for example. Hope this helps!
2_8_2018_2_19_17_pm.jpg

Home Fencing | Answered on Feb 08, 2018 | 432 views


700 + 264 =964 perimeter

Home Fencing | Answered on Dec 25, 2017 | 936 views


Remove all batteries for 1 minute, should work

Home Fencing | Answered on Dec 25, 2017 | 1,248 views


Check to see if the screw retractor is stuck.

Home Fencing | Answered on Dec 25, 2017 | 522 views

Not finding what you are looking for?
Hino 2006 268 Logo

9 questions posted

Ask a Question

Usually answered in minutes!

Top Hino Home Fencing Experts

Tom Chichester

Level 3 Expert

60224 Answers

 Russ Hill
Russ Hill

Level 3 Expert

4057 Answers

ray gallant

Level 3 Expert

70798 Answers

Are you a Hino Home Fencing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...