Sanyo TRC-8080 Desktop Cassette Voice Recorder - Answered Questions & Fixed issues

Just record over it unless you have an erase button.

try the local electronic device repair shop ..cause this is not a complicated intervention ..it is either the motor belt that snapped out or broke ..(in this case will not play either ..) or it is just the button or the contact to it ..and it is resolved in a few minutes....

Hello Sorry but the Model Sanyo TRC-8080 is not Recorder is only a transcriber the Sanyo Model Sanyo TRC-8800 is a Dictator and trancriber if you are looking for a good unit this is a good alternative http://www.tvps.com/Products/Dictaphone-2720-Standard-Dictator---Pre-Owned__DI-P-2720-D.aspx

Hello I recomend to send it to service sound like a Motor problem Send an email to [email protected] or call (800) 644-9525. Please indicate model, serial and detailed description of problem

Hello your unit may have a desolder autobackspace slide control or maybe your pedal is going bad here is a link for your pedal replacement http://www.tvps.com/Products/Sanyo-FS-56-Transcription-Foot-Pedal---Pre-Owned---FS56__SA-P-FS-56.aspx or send your unit to service at Send an email to [email protected] or call (800) 644-9525. Please indicate model, serial and detailed description of problem

Hello when hapens you need to replace the inside contact switches if you want to send it to repair send it to Send an email to [email protected] or call (800) 644-9525. Please indicate model, serial and detailed description of problem

Hello. The TRC8080 will coontinously beep when trying to record if the tab switch (this is described in the service manual a Tab Switch S3, S4) fails. The tab switch consists of two leaf switches one is so the machine know there is a tape in the machine and the other check for record protect. Over a period of time thee canbecomebent anwill not always connect when a tape is in. This wll result in you either not being able to play a casette or not being able to record depending on which one fails. These can only be replaced as a pair. If it is not the tab switch which has failed then the cassette tabs on the top may be bent in slightly which means you will need to replace the cassette.

If the tab switch has failed and you dont want to pay for a repair you take the 5 screws out of the back of the machine, lift the top cabinet off (disconnect the single molex connector) and short the switches together. (Solder is best) this will leave the switches perminatly in the 'on' position meaning you can dictate away.

Remember if you shoose to short the switches together the motor will run as soon as the cassette lid is closed and the machine is on. This may make the motor fail a little bit earlier than normal.

The motor has gone and would need replacement. Unfortunately, this part was recently discontinued so you will have trouble finding someone who has one.

Video recorder? Please state model number.

from description given the unit is defective.

Hi,\015\012\015\012I'm sorry to hear that.\015\012\015\012This is a common fault on cassette decks and can be caused by a number of things.\015\012\015\012The most common is the motor being seized or worn.\015\012\015\012If the motor spins when you touch the belt then the problem lies in the drive mechanisms.\015\012\015\012There is a good chance that the drive belt has perished and needs to be replaced.\015\012\015\012If the deck is drawing too much current when you switch it on the fuse will blow.\015\012\015\012If the fuse is fine and the deck runs for a few seconds before cutting out then the problem could be one of the capacitors in the power supply.\015\012\015\012If the deck is more than 10 years old then it may be time to replace the capacitors.\015\012\015\012You can do this yourself if you are a little bit handy with a soldering iron.\015\012\015\012That's about it really.\015\012\015\012

https://www.manualslib.com/manual/1069169/Sanyo-Rm-5090.html

When the tone arm returns to its base it should contact a small micro switch which turns off the motor. Going underneath the platter you should find the switch, either bent out of place or broken.

Is your tv compatible with wireless speakers?

Use code search on your Sanyo URC to find something that works. If a search through all codes stored in the URC fails, try a different one.

There might be a diagram but I haven't seen any belt fitting diagrams at all, merely the odd exploded view. Replacing cassette belts is as much fun as a jigsaw puzzle - you keep removing screws and parts until you can fit the belt and then you reverse the process...

Hello Hannes, FM ANT, is the connection of the antenna to receive FM radio stations (Frequency Modulated) Here you can connect a cable of approximately 1 meter, and use it as an antenna, depending on where you are, rural or remote areas. the city, you might need an external antenna, similar to those used for analog TV reception I sent you a link to download the user manual of your Sanyo Greetings Franco Dosil Hola Hannes, FM ANT, es la conexion de la antena para recibir estaciones de radio de FM (Frecuencia Modulada)Ahi pedes conectar un cable de 1 metro aproximadamente, y lo usas como antena, dependiendo de donde te encuentres, zonas rurales o alejadas de la ciudad, podrias necesitar una antena externa, similares a las usadas para recepcion de TV analoga te envio un link para que descargues el manual de usuario de tu Sanyo Saludos Franco Dosil https://mans.io/files/get/499596 https://mans.io/item/sanyo/dc-da1460m https://elektrotanya.com/sanyo_dc-da1460m_micro_component_system_sm.rar/download.html

Hello Walter, what do you want to repair in your Sanyo DC-D37U, the mechanism of the CD player? I sent you the link to download a Service Bulletin of those mechanisms I hope you can repair it, comment the results Greetings Franco Dosil Hola Walter, que es lo que quieres reparar en tu Sanyo DC-D37U, el mecanismo del reproductor de CD? Te envio el link para que descargues un Boletin de service de esos mecanismos Espero puedas repararlo, comenta los resultados Saludos Franco Dosil https://www.dtforum.info/index.php?action=dlattach;topic=7137.0;attach=9887

fixya doesnt do appraisals

Hi Paula, check the HDMI input, on the Sanyo TV, where the cable box is connected, it is assumed that the channels are loaded in said box Hola Paula, verifique la entrada HDMI, en el televisor Sanyo, donde esta conectada la caja de cable, se supone que los canales est?n cargados en dicha caja