20 Most Recent Sharp AR 163 Copier - Page 9 Questions & Answers

First try removing the fax telephone line, then remove the power plug for 5 minutes. Plug in the power and reconnect the fax line. If that fails, System Reset https://www.google.com/search?q=sharp+ar-m201+factory+reset ..

F2 code means a problem with toner cartridge error. Sometimes F2 is caused by loss or broken harness in the scanning section, in this case, it sometimes displays an E7 code. When f2 flashes on display just press the Start key you will receive a subcode. If the subcode is F2-02 this is a toner supply problem. If the F2-04 toner chip is damaged, replace the chip. If the F2-40 developer is damaged, change the developer

• Clean toner cartridge CRUM chip contacts and check if cartridge destination is proper for your area.
• This code you may have to clean out the developing unit and start with a fresh developer. Make sure the developer unit is not leaking from one of the bearings. You may need a tech for this one.
• Replace the toner cartridge.
• Change the developer.

If you find your parts, then replace the parts and error still remains, after automatically reset the error code. If the error is still showing even after the above solutions, then you have no choice other than calling Sharp service technician.

L1 at sharp 5520

Hold down the blue house button on the main menu until the toner levels and meter reading is displayed. Tap the toner remaining tab and the device will display your current toner level.https://business.sharpusa.com/portals/0/downloads/Manuals/MX-M1055-M1205/contents/01-072.htm

Check CCD unit harness. Check CCD unit. Check scanner PWB.

https://copacobana99.cyou/

https://www.fixya.com/support/t26906995-error_code_ch_blinking_in_sharp_6020

call Sharp's Customer Assistance Center at 1-800-BE SHARP Such is the advice in the manual.

Sounds like your que is full and possibly locked. Might be the hard drive is gone ,or you just need to go into the que and empty it manualy.

So far, I've seen 2 faulty Pastel2 LSU's within the first week of installation. All run-up and first week operation & testing is OK, then the LSU goes down.

Run the LSU test in sim 61. If you get result NG, you have a dead LSU. If the error disappears, keep an eye on it for now, but you may need a new LSU soon. Just warning you.

I would contact Sharp for advice.

https://sosnfl.com/sharp-mx-c312-error-codes/ https://printcopy.info/?mod=erc&brand=Sharp&model=MXC312SC&code=L4-12

Depends on which sensor you think may have failed.

That doesn't look like a Cellphone! Picture graphic looks like a photocopier? Presumably 'Are' is supposed to be 'Our', but no one knows what a 620 is? Google thinks it is a Wire Tracer unit!PLEASE, FULLmake model (what it is)in all questions and put it in the correct category.AHA, this is a Sharp AR-6020Orange Bang out triangle can be anything. Remove paper trays, remove toner, open all the doors, and look for paper misfeeds. Disconnect the power for 30 seconds. Replace everything and connect power.https://www.google.com/search?q=Sharp+AR-6020+copier+error+codes..

No spares. Time for a new one https://www.ebay.com/itm/Sharp-EL-1197S-Electroinc-Printing-Calculator-For-Parts-/224193625453 https://www.google.com/search?q=Sharp+EL-1197S+spares ..

A clean and service will sort that out if the drum is OK.

define integral??

C4-30 is a transfer corona wire issue. May be shorted out due to dust and carpet fibers. Try spraying it with canned air to clear out what may be shorting it out Good luck !

https://printcopy.info/?mod=erc&brand=Sharp&model=MX6240N&code=F3-12https://www.google.com/search?q=sharp+mx+6240n+error+code+f3-12&source=lmns&bih=625&biw=1366&hl=en&sa=X&ved=2ahUKEwjHjoqR2qDvAhWYlUsFHa4SDbQQ_AUoAHoECAEQAA

H4-21 means: Sub heater lamp abnormally low temperature detection. The setup temperature (about -25°C: Sim 43-1-1) is not reached within the specified time (about 32sec) from turning on the power ON SW. (When the temperature falls below 140°C in the standby mode.) -Check the sub heater lamp blinking with SIM 5-2-2.