20 Most Recent Sharp AR-407 Copier Questions & Answers


H3-00 means there was a problem in the fuser unit of the copier - a temperature problem. The correct temperature is not reached within a certain time.
It could be a thermostat or thermistor problem - both monitor temperature. you could remove the fuser unit and make sure these items are clean - no build up on them. there should be a center and side thermistor.
You can reset the error code in SIM mode by pressing the following keys one after the other "P" "interupt" "C" "interupt" then 14 and start/copy key. confirm if required. make sure the copier is restarted afterwards.
If the error persists then you may need new thermistors.
Hope this helps.

Sharp AR-407... | Answered on Jun 05, 2017


fuser problem check it.

Sharp AR-407... | Answered on Jan 07, 2014


Please check fusing unit first.

Sharp AR-407... | Answered on Jan 07, 2014


h3 01 on sharpcopy 407 what is the couse and solution

Sharp AR-407... | Answered on Dec 01, 2011


If you are getting a "circling stars" picture on the LCD screen your hard drive in the copier is bad.

Sharp AR-407... | Answered on May 31, 2011


Cause: Paper jam in fuser unit or paper jam removed beyond required time.

solution: remove jam from fuser unit.....perform simulation 14 to reset machine!!!

Sharp AR-407... | Answered on Feb 23, 2011


F2 02 Toner motor connector unconnected

Content: Toner motor connector unconnected
Detail: Connection detection signal with toner
motor is OFF
Cause: Connector harness defective
Connector disconnected
Check and remedy:
Check toner motor connector for
connection.
Check connector harness to main PWB
for connection.
Check harness for broken wire.

Sharp AR-407... | Answered on Jan 30, 2011


There are a lot of choices for F2-?? Hold down the Start button to see the remaining digits.

Sim 22-6 will print all jam codes & error codes. It should be a process control code. F2-31 or F2-37, Drum mark or image density. You can execute 44-6. This should show which is out of range. Pull the drum unit out & clean both sensors. Check that the blade is cleaning from end to end that the DM is visible to the sensor.

Sharp AR-407... | Answered on Dec 26, 2010


Hi Franck,
H3-00 means there was a problem in the fuser unit of the copier - a temperature problem.
The correct temperature is not reached within a certain time or an overheat, It could be a thermostat or thermistor problem - which both monitor temperature.
You could remove the fuser unit and make sure these items are clean - no build up on them, There should be a center and side thermistor.
You can also reset the error code in SIM mode by pressing the following keys one after the other:

" P " " interupt " " C " " interupt "
Then 14 and start/copy key. Confirm if required and make sure the copier is restarted afterwards.

If the error persists then you may need new thermistors.
I hope this helps.
Warm regards and merry christmas.
Mike

Sharp AR-407... | Answered on Dec 23, 2010


On the AR-407:

To remove the developer/toner cartridge, there is a green lever inside the front door/cover. Pull it down like you are going to refill the toner, pull it out, and there is a release lever on the right side bottom, between the cartridge and the copier. This will release the cartridge and allow you to slide the whole mechanism out.

There are 4 screws that hold the toner box onto the developer. (NOT THE TOP MOST COVER SCREWS) 2 on the left side (with the toner hopper on your right), and 1 screw on the right top, and 1 screw on the right side by the handle you use to pull the cartridge out of the machine. Make sure you also disconnect the electrical connector that attaches to the hopper motor.

Be careful not to spill the toner or developer as you are seperating the two.

The developer unit is the bottom unit.

Dump out old developer (make sure you get all of it by turning the gear on the back side). If you don't have a toner/developer vacuum, then just get as much out as you can. A normal vacuum motor will eat itself in a very short time trying to vacuum up toner or developer, because the particles are too small for a regular filter.

When you get all the developer out, then carefully open the new developer packet, and evenly pour it in. Put it back together the same way you took it apart.

Reset Developer counter : Simulation 24-5

Hope this helps!!
Ryan K

Sharp AR-407... | Answered on Nov 02, 2010


Problem with the NIC card or network controler

Sharp AR-407... | Answered on Aug 17, 2010

Not finding what you are looking for?
Sharp AR-407 Copier Logo

59 questions posted

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

k24674

Level 3 Expert

8091 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6960 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sharp Office Equipment & Supplies

  • Sharp Office Equipment & Supplies

Most Popular Question

f2 02

  • Office Equipment & Supplies
Loading...