Top 20
Samson Auro D412A Speaker PA Active Questions & Answers
Hi,
I have one Samson Auro
If you read the TRUE specs on this speaker it is really a 200 Watt RMS unit. Make sure you are using balanced lines to the speaker XLR or TRS cables. The mixer should NOT be a passive mixer as these do NOT generate true balanced lines. Make sure the mic can't "hear" the speaker or you may be getting supersonic feedback that is above your hearing range that saturates the amp. If *********** can't stand to be ain a 15 foot square room with teh level you are generating, it is TOO loud for this unit to handle.
After working great for over
This is a bi-amped speaker. That means it has a separate power amplifier driving the bass woofer and treble horn. They have a low-level electronic crossover to separate the frequencies to the appropriate speaker. The electronic crossover is the least likely to fail... so you need to do a test:
You will need to open the unit and using an ohmmeter check if the woofer speaker voice coil is open or has continuity...It should be around 6 to 16 ohms. If it is above that, the speaker itself is blown and will have to be replaced. If the speaker has continuity, then the bass amp has failed and will require repairing by person that is adept at electronic repair. Before opening the unit you MIGHT be able to diagnose whether the speaker itself is blown by seeing if the woofer generates a thump when power is turned on or off. If it does, then likely the speaker is OK and the problem is the amp, otherwise the tests above need to be done. Usually these plastic cabinets are held together with seveal scrwes from the back. Some are in :deep "wells" and will require a very long shaft phillips screwdriver... and they often are long screws that wear one out unscrewing them. A genlte pry after removing the screws will separate the back and the front.
What do I need to
Connection all depends on what type PA system you have. Here are the rules: Power this device from the SAME receptacle your mixer is powered by, even if it means running an extension cord. Use ONLY a balanced line from the mixer... either TRS cable or XLR cable.
Samson MDR8 blowing internal power supply fuses.
Here is a troubleshooting hint:
Put an incandescent lamp in series with the hot side of the power cord. This acts as a resetable fuse while troubleshooting so you don't blow fuses.
Schematics are hard to come by, but power supplies are easy to trace the circuitry.
Check filter caps and the diodes and THEN look for hot (temp) IC's and transistors.
3/17/2010 12:58:34 PM •
Samson Music
•
1,746 views • 1 helpful votes
How do I do transposition in e16 Roland?
To transpose a sound on the Roland E-16 keyboard, you can use the Transpose function. Here's how to do it:
- Press the FUNCTION button and then press the TRANSPOSE button.
- Use the + or - buttons to select the number of semitones you want to transpose the sound. The range is -12 to +12 semitones.
- Press the EXIT button to exit the Transpose function.
Once you have transposed the sound, it will be played back at the new pitch. Keep in mind that transposing a sound may affect the overall tone and timbre of the instrument, so you may need to make additional adjustments to achieve the desired sound.
3/19/2023 5:38:45 AM •
Music
•
125 views • 1 helpful votes
Casio Privia PX-135 sound issues?
It sounds like you are experiencing a problem with your Casio Privia PX-135 keyboard. There could be several possible causes for this issue, including problems with the keyboard's internal hardware or software, or issues with the cables or connections between the keyboard and other equipment.
To troubleshoot this problem, you could try the following steps:
- Check the connections between the keyboard and any other equipment, such as an amplifier or speakers. Make sure all cables are securely plugged in and not damaged.
- Try a different set of speakers or headphones to see if the issue is with the keyboard or the output device.
- Check the keyboard's settings and make sure that it is configured correctly.
- Try resetting the keyboard to its factory default settings. This can often resolve issues with the keyboard's software or firmware.
If none of these steps help, it is possible that
1/1/2023 10:10:07 PM •
Music
•
81 views • 0 helpful votes
Not finding what you are looking for?