Top 20 Shop Vac 333-32-08 Blower Vac Wet/Dry Vacuum - Page 6 Questions & Answers

If your Haan steamer is not turning on, there could be various reasons for this. Here are some troubleshooting procedures to assist you in identifying and maybe resolving the issue: Check the Power Source: Make sure the steamer is plugged into a working power source. Check if the outlet is operational by using another device or appliance. Inspect the Power Cord: Look for any visible damage, such as frayed or exposed wires, on the power cord. If there is any damage to the cord, do not use the steamer until it has been fixed or replaced. Safety Locks and Buttons: Some steamers feature safety locks or buttons that must be engaged before the unit will turn on. Check the user handbook for any special instructions regarding these safety measures. Water Reservoir: Ensure that the water reservoir is appropriately filled. Many steamers require water to generate steam, therefore they may not operate if the reservoir is empty or the water level is too low. Safety systems: Some steamers have safety systems that prohibit them from starting if specific requirements are not satisfied. For example, the steamer may need to reach a certain temperature before it can be used. Allow the steamer some time to attain the required temperature. Overheating Protection: If the steamer includes overheating protection, it will stop down briefly if it becomes too hot. Allow the steamer to cool before using it again. A malfunctioning power switch or electrical circuitry could be the source of the problem. If you've examined all of the external causes and the steamer still won't switch on, it may need to be inspected and repaired by an expert. I hope you can solve your problem.

you will to take motor to motor shop, disassemble motor and take bearing shop, OR buy a new motor for less money copy and paste link https://evacuumstore.com/p-9980-sanitaire-commercial-upright-sc679-j-motor-assembly.aspx

That's weird. When the handle is up on the Hoover WindTunnel T-Series U6439-900 Bagless Upright Vacuum Cleaner, the brushroll will not run. This vacuum is designed to run the brushroll only when the handle is in the lower (or operating) position. I'd suggest contacting Hoover for help.

Question edited for clarity, add CAPS and spaces. No one has done this yet, and it is a virtually unknown brand, at least in North America. https://www.google.com/search?q=johnny+vac+222+disassembly You could ask them https://www.johnnyvac.com/en/all-parts ....

This question needs 'make model what it is)' please as first 3 words. https://www.google.com/search?q=1698+series ..

save to favorites https://www.youtube.com/watch?v=iDJFge5EptY https://www.lakeland.co.uk/content/documents/46386_label_2.pdf

Hello Shelley The loud whining sound could result from an obstruction within the various parts of the machine, like the noizzle or suction pathway.Check the motor could be having a problem

Can be either
1hair, debris around the brush roller
2 brush roll bearings have hair Etc, right on them

3 brush roll bearings worn badly .
Do they turn freely, take out and turn while putting light pressure with fingers, light twisting

4 belt issue,
Did the belt before this one break or wear maybe too soon which points back to Roller/ bearings/ hair

https://everettvacuum.com/blog/check-your-brushroll-bearings

Very little on this little known appliance. It make be the thermal overload fuse. Take it to a local repair shop or you could strip it down, identify the fuse and test it with a Digital Test Meter. https://www.google.com/search?q=Amy+HAAN+FS-20+steamer+will+not+turn+on ..

The belt is part of the pump that delivers the cleaning solution according to an unverified source.. You might query Hoover. . https://www.amazon.com/Hoover-440005353-Original-Equipment-Manufacturer/dp/B00F9A4FJI Also works with FH50252 Hoover Power Scrub Elite Pet. https://www.youtube.com/watch?v=yEbRVwRhsPg How to Replace a Hoover Shampooer Hose Pump Spin Scrub - YouTube which I am informed applies to your Hoover as well. Sorry I cannot provide a more direct answer. Try Hoover customer service.

Full 'make model (what it is)' is needed in all questions on Fixya please. The drive belt is broken whether it is a standalone upright cleaner or whether it is a canister vacuum with a hose and wand with brush head. How you replace it is completely dependent on make and model, but can easily be Googled or refer to the manual.

There is probably a blockage in the pipe or on the entry to the motor. I would take it to pieces and clean it.

Hold the unit aloft, then tap lightly with a rubber or wood mallet all the way around the filter housing, try turning it then repeat process, it should come off eventually.

1. Check the drain system: Make sure that the drain valve or plug is fully closed and not leaking. If there is any water present, drain it completely before proceeding.
2. Reset the unit: Turn off the unit and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again. This can sometimes reset any error messages and resolve the issue.
3. Check the water detection sensor: The unit may have a sensor that detects the presence of water in the tank. Look for the sensor and make sure it is clean and free of any obstructions. If there is any dirt or debris on the sensor, clean it gently with a soft cloth.
4. Contact customer support: If none of the above steps work, it's best to reach out to the manufacturer's customer support for further assistance. They can provide specific troubleshooting steps for your particular unit and guide you through the process of resolving the issue.

Remember to refer to the user manual that came with your unit for specific instructions and recommendations.

If the cap on your Living Solutions steam vac won't stay down, it could be due to a couple of reasons:

1. Incorrect positioning: Make sure the cap is properly aligned and seated on the unit. Check if there are any obstructions or debris preventing it from fitting securely. Clean the cap and the sealing surface if necessary.
2. Damaged or worn-out seal: The cap may not stay down if the seal inside is damaged or worn out. Inspect the seal for any signs of cracks, tears, or deterioration. If it's damaged, you may need to replace it. Contact the manufacturer or refer to the user manual for guidance on obtaining a replacement seal.
3. Defective cap or pressure release mechanism: It's possible that the cap or the pressure release mechanism itself is defective. If you've ruled out other causes and the issue persists, you might need to contact the manufacturer's customer support for further assistance. They may be able to provide troubleshooting steps or offer a replacement part if needed.

Remember to always follow the manufacturer's instructions and safety guidelines when working with steam cleaning devices.

Impossible to guess what you have Google make model height adjustment repair All questions need 'make model (what it is)' as first 3 words please. https://www.google.com/search?q=%E2%80%8Bmake+model+height+adjustment+repair ..

Question edited for clarity. Help and Support in the link https://www.google.com/search?q=Rug+Doctor+PSC-1+reassemble+handle

Question edited for clarity. Blinking White Light = The robot is upgrading or resetting. It it never stops, contact their Support https://trifo.com/pages/support ..

The slip ring contacts at the canister end of the Miele SES 125-3 hose are responsible for transmitting electrical power to the motorized brush head. Over time, the slip ring contacts can become dirty or corroded, which can cause the brush head to stop working properly. Here are the steps you can follow to restore the slip ring contacts: Unplug the hose from the vacuum cleaner and remove the brush head. Look for the slip ring contacts inside the canister end of the hose. You may need to use a flashlight to get a good view. Use a small brush or a cotton swab to gently clean the slip ring contacts. Be careful not to apply too much pressure, as this can damage the contacts. If the slip ring contacts are heavily corroded, you may need to use a mild abrasive to remove the corrosion. Be sure to use a non-abrasive cleaner specifically designed for electrical contacts. Once the contacts are clean, use a dry cloth to remove any excess cleaner or debris. Reattach the brush head and plug the hose back into the vacuum cleaner If the slip ring contacts are damaged beyond repair, you may need to replace the hose or take it to a professional for repair.