20 Most Recent
Hitachi CLU-4324UG Remote Control Questions & Answers
Codes
You have to get into the devices' service mode to cancel the old password.
If you wish to get more details, surf the
following link. There are over two thousand and four hundred posts. All are
related to television and other domestic electronic equipment service help. You
can get a solution there. Type in the brand name to your device to its search
box, can be located at the top right of the display window. It will make search
easy. More than Nine Lakh viewers cannot be wrong.http://electronicshelponline.blogspot.com/
5/11/2013 10:41:46 AM •
Hitachi...
•
Answered
on May 11, 2013
Show how to work a hitachi remote
If you wish to get more details, check this
site. Pull up previous posts
there. Setup code list and
setup proceedings to many popular brand remote controls are given. Three digit, four digit, five digits and
two-digit code list are there. Check
the site with patience. Surely you'll
get a solution to your problem. Search
the site by 'Timeslide' option. It will
make search easy. Or, type in the brand
name to your device into its search box, and press "Enter"
4/4/2013 2:37:15 PM •
Hitachi...
•
Answered
on Apr 04, 2013
Our remote is the CLU-4324UG
Helo
If the remote control you uses with your Hitachi is a universal one, there will be some malfunctions occur with remote button presses and TVs response. If it is its original one, the remote controls keypad circuit prints comes at the back of keypad is dirty. You have to open it, and clean it with medical quality turpentine or recitfied spriit. Never use hard solvents like petrol or so, as it will damage the rubber pad of the remote control.OK.
7/6/2011 2:19:25 PM •
Hitachi...
•
Answered
on Jul 06, 2011
How do I get the
There is a button labeled TV/AV , press it to get out of Video mode.
6/16/2011 3:30:37 AM •
Hitachi...
•
Answered
on Jun 16, 2011
I have a Hitachi CLU-4362S remote that I am trying
Hi my nameis Mike Houston of DISH Network; I was going over your post and see where youwant the Hitachiremote to work the DISH receiver and your DVD. The best thing to use is theDISH Network remote to use all the functions of the receiver; I will send thislink
http://www.hitachi.com and theinstructions of programming the Hitachiremote.
5/2/2011 1:28:40 PM •
Hitachi...
•
Answered
on May 02, 2011
One of the buttons does
more then likly it will be motherboard for your remote if you can take it apart and see if can a break in the curcuitry if so scrape it back to expose copper then repair using liquidwire about 10 bucks from most electronic stores its just a glue very ezy to use works like solder but is a glue if no break in curcuitry then try looking at rubbers on the back of the buttons hope this helps
4/11/2011 12:15:16 AM •
Hitachi...
•
Answered
on Apr 11, 2011
RCA TV Model F32685
if cable network in tv is using a digi.box with a scrat to the tv, then just unplug scrat and plug it back in, make sure it is fitting corretly-if not working then change scrat lead,
If no digi.box in use redo connection that is there.
In most cases its not the tv. at fault.
3/1/2011 12:27:59 AM •
Hitachi...
•
Answered
on Mar 01, 2011
Remote works for power and volume but nothing
Hello,
Common faults are: some buttons not working, not working at all, corroded battery terminals. Often buttons are sticky because of some dirt accumulated over the years from the sticky little hands of your kids?
The hardest part of repair is often to open the covers. You do not need much experience in electronics repair to repair a remote. Also it is perfectly safe as there is no way to get an electric shock as they work with batteries.
step 1Test your remote with Digital Camera
Check your batteries first or buy new batteries. Once you have good batteries, you can test with a digital camera by pushing the buttons and having camera on and pointing to the infrared led. You should see red light if the remote is working. If no light comes up you obviously have a dead remote but do not despair and proceed to the next step
step 2Open the remote control but there is a catch or a few catches.
Remove the screws if any. Sometimes screws may be hidden under a sticker or rubber feet. Often there are no screws at all but just plastic catches hidden so you have to be clever to open it without breaking the case. Use something blunt and flat to click the covers open. This is often a challenge but should not be too difficult.
step 3Take a picture of every phase so you remember how to re-assemble
Since you are using a digital camera you might as well take pictures of the dis assembly so re-assembly will be easier.
step 4Pull everything apart
Did you take a picture of the keyppad layout? Sometimes keypad is just one rubber membrane but sometimes the keys fall away like pieces of a Lego puzzle. And if the buttons are marked with numbers and functions you may struggle to re-assemble them in right order? Use a small plastic takeaway box or similar to store the bits so you don't lose parts.
step 5Inspect the circuit board and repair dry joints
Remotes are often dropped on the floor and may develop dry joints on the battery contacts or circuit board. Inspect the contacts and circuit board under good light with a magnifying lens or if lucky you might have a microscope or just a very good eyesight? Solder all suspicious joints. If there is a sign of water damage you can use methylated spirits and toothbrush to...
step 6Wash the covers and the buttons
Use a small bowl or similar to wash and contain all the parts so you don't lose bits down the drain. Use old toothbrush to clean all button holes and buttons. Warm water with dish wash liquid does the job. Take particular care with those small buttons and clean them properly. If you can leave the bits to soak overnight they come clean easy. Ultrasonic cleaner would be goo...
step 7Rinse, drain and dry the parts
Rinse with warm water. Use a drainer to contain all the parts without losing small bits down the drain. As extra security use sink plug. Dry with a paper towel. Wipe the buttons dry individually as they may still have some dirt which makes them sticky when in use.
step 8Repair case and re-assemble
If there is damage to the case or buttons you need to do the required repairs. Use hot glue or super glue depending on fault. Let dry overnight if you had to glue something. Re-assemble bits in reverse order and make sure you have the buttons in right place and right way around. Small nicks and dents on plastic cover can often be repaired by heating carefully with a h...
step 9Test with Digital Camera
Test every button as before. Sometimes you have to push two remote buttons simultaneously . Once you have completed test with your camera you can use the remote.
That's it, I hope you got it going again?
"Dead" Remotes Can Be Saved
12/14/2010 9:11:13 PM •
Hitachi...
•
Answered
on Dec 14, 2010
Remote code
You won't be able to use it for your dvd player unfortunately.
The code for sky is 0145.
1) Switch on the TV set
2) Press the TV button on the Sky Remote
3) Hold down the select and red buttons for 2-3 seconds until the LED blinks twice
4) Press the TV button on the Sky Remote again
5) Enter the 4 digit code for your make of TV
6) The LED should blink twice, if not recheck the 4 digit code used and go back to 1
7) Press the standby button on the Sky Remote (The TV should go to standby)
8) Press select to store this setting
If the TV does not go into standby press the TV button then the standby button, then TV then standby, keep repeating this until successful.
Gaz
5/4/2010 2:48:07 PM •
Hitachi...
•
Answered
on May 04, 2010
Channel up bottom must push very hard to change
Could be dirty contact between board and pad or the board could be cracked. This requires you to open the remote up which can be done if you are careful and take your time. This is a common problem if something gets spilled on the remote and seeps between the board and pad. Usually a damp soft cloth and and blow drier to make sure it is completely dry berore reassembly is the key!
3/15/2010 5:10:16 AM •
Hitachi...
•
Answered
on Mar 15, 2010
Not finding what you are looking for?