Canon imageRUNNER 8500 Copier - Page 7 - Answered Questions & Fixed issues

I don't know of any free manual downloading sites, but here is a site where you can buy them for a reasonable price.

Check the fuser rollers for wear. When this occurs the rollers lose their roundness and get flat spots on them. This can cause the thermistors and thermal switches to bounce on thier surface and get incorrect readings. Should replace upper and lower fuser rollers every 150,000 copies (A4).

I need manual service for Canon IR8500

A E240 is the reg. clutch or the DC controller or a loose wire, a E246 to me would be a problem with the DC controler or a loose wire going to the pcb. And the E225 or E226 has something to do with the counter pcb or the DC controler pcb. Also I would check the rom version of the copier. Also, was that the problem you went there for?? If not retrase your steps..

can you be more specific

are you trying to find the send email in your send item Box?

Need more info.... Is it pitch line accross the page the whole page or banding on the front or back side of the copies or is it black streaks down the page?

the feed screw in side the waste toner pipe prevented from rotating.remove the waste toner pipe,and try turning the screw by hand.If it turns easily,mount it back again and see if the problem is corrected.Otherwise,replace the waste toner pipe,and remove thecause.
make the following selections in service mode
COPIER>I/O>DC-CON>.is bit 6 of P003 is 0.replace MSW2.if its not 0 replace DC controllor PCB.

The laser assy is unservicable.

just replace the duplex moter.

Having trouble with my IR8500 getting Error code E000218-0000. Any Suggestions? Thanks

Hello Jeremy,
This error code has to do with your finisher. The auxillary tray is not finding its home position or does not leave the home position within the alotted time. Check for binds. I have limited exposure to the K4/3 finisher but try this. Turn the copier off, and open one of the finisher doors. Now turn the copier back on with the finisher door open so it cannot initialize. Once the copier is basically ready except the finisher door is open, close the finisher door and observe all the **** (and theres alot) initialize. This may help determine the problem. I hope this helps...........................SPINAL

i know what the problem may be call 0776 4303923
advise is free

With acrobat full version and network scangear, or you can buy the option "send kit" .

Hello PE. I will tell you what the code means and although we can reset the code, if the PROBLEM still exists I am afraid the code will of course return when the copier performs a diagnostic. By telling you the reason for the failure perhaps you can fix the problem and therefore MR. COPIER wont be pissed. :-) This code means that the paper supply referred to as tray "B" has a problem.The lift motor for that paper supply could not (or the copier believes it could not) successfully lift the paper to the correct paper heighth required to feed the paper. This explanation may help you correct the problem.Now to clear the code. On the operator control panel next to the nine key pad is a button that says "additional functions". That button will be part of a 3 step process. Press the the additional function button>>>> next press the numbers 2 and 8 together at the same time>>>> then back to additional functions button.This is a 1,2,3 process that should be executed in a smooth but timely fashion. This will bring up a new window on the screen. Ther will be several "blocks" on the screen and one will say COPIER. Press copier.Then a new screen appears with several tabs across the top. One of those tabs will say FUNCTION. Press function.The screen will be filled with an assortment of blocks and one will say CLEAR. Press clear, and a new set of blocks will appear.One of the new set will say ERR. Press err and then in the lower right hand corner you will say a block saying "OK". Press ok. Now unplug the machine and wait a few seconds and plug it back in.You WILL have successfully erased the error code and the machine will perform its power on diagnostic as if nothing was ever wrong. However if the problem still exists the copier will see it and the code will return. If it does, you can perform the process again but this time pull tray "B" out so the copier cannot run a diagnostic on it. This is merely a workaround and will allow you to use the copier and its remaining paper supplies. As to what specifically the problem with paper tray "B" is could be several things, all of which would require a tech to come out. I must assume that is what you are trying to avoid (as would I ....$$$$$) I hope this helps you and I wish you the best. SPINAL

www.precisionroller.com

hi im jules_09,theres a problem with the copier because ussually after turning it on it warms up for seconds or a minute,but when it freeze at wait the warm up time is too long,see if if you can get the error code,if there is a error code it the lcd check how long is its warm up time.if it take too long.if you can repair it check the voltage at the power supply board going to the main logic board.

Press
*
82 Simulatneously
*

hi im jules_09.the opc drum of canon is not needed to be polish,they are sensitive to any form of polishing materials,but if the drum is not scratch adjust the voltage on your exposure lamp in the program.if its still light somrthings wrong with your developer

This error occurs when the stapler assy hasn't moved back to home position upon start up. This could suggest that the stapler assy has become free of its runners and crashed into the paper delivery assy. Try and see if you can get it back on its runners through the stapler door. If not, call an engineer. Hope this helps.

This explains why there is no online support for Canon varioPrint machines. The website CopyTechNet is my go-to solution for help. https://www.copytechnet.com/forums/canon/147237-need-help-varioprint-135-service-manual.html https://www.google.com/search?q=Canon+Varioprint+110%2C+code+6527 ..