20 Most Recent Canon imageRUNNER 8500 Copier Questions & Answers

i just replace Stapler shift motor GEAR..its work!!


Canon... • Answered on Dec 12, 2019

Hello Jeremy,
This error code has to do with your finisher. The auxillary tray is not finding its home position or does not leave the home position within the alotted time. Check for binds. I have limited exposure to the K4/3 finisher but try this. Turn the copier off, and open one of the finisher doors. Now turn the copier back on with the finisher door open so it cannot initialize. Once the copier is basically ready except the finisher door is open, close the finisher door and observe all the **** (and theres alot) initialize. This may help determine the problem. I hope this helps...........................SPINAL

Canon... • Answered on Jun 27, 2019

Error E354 in Canon iR 2016error e354 code appear when you replace PCB controller board.Please note. Before replace your PCB board with other one.Pull out a small (FRAM COUNTER) chip from your old PCB board you can found it right side of the PCB board near a battery cell the chip attached with screw open screw and pull it out and attached it with your new PCB board .install your PCB board in the machine and turn on power error e354 will go off.

Canon... • Answered on May 05, 2019

error E061 poblem

Canon... • Answered on Apr 13, 2019

Turn on holding down 1 and 9 keys. will go through a long complete format. If blocks do not fall down through screen left to right, HDD is completely gone.

Canon... • Answered on Aug 31, 2018

Having trouble with my IR8500 getting Error code E000218-0000. Any Suggestions? Thanks

Canon... • Answered on Aug 24, 2018

3320i error code E000537-0000

Canon... • Answered on Apr 20, 2018

ir 8500-E000100-0000

Canon... • Answered on Mar 29, 2018


Canon... • Answered on Jun 24, 2017

Main controller PCB
1) Turn offf and then on the power switch. Is the problem corrected?
YES: End.
NO: Replace the Main controller PCB.
Control panel PCB
2) Try replacing the control panel PCB. Is the problem corrected?
YES: End.

Canon... • Answered on Feb 16, 2017

my copier not working only display the download mode.

Canon... • Answered on Jan 14, 2016

A E00061-0001 deals with the drum charge is missing. I would look to see if the primary charge unit is installed correctly, if so I would pull the unit out and make sure none of the corona wires are broken.. could be one of the post wires or the grid is broken. You may also, have a end block that is arching out. If you are not a service tech, you will need to call one to repair the code. It can't be cleared till it is fixed... Good Luck

Canon... • Answered on Jul 15, 2015

hai,one ir6000machine in oneand most problem eo61-01 please solution in this problem thnk you.

Canon... • Answered on Feb 19, 2015

hello 8500 IR copy machine E00015 - 0000 errors. Please guide me. I also translated by the site you have to translate the sentences. So you have the goodness wording is easy. Thanks

Canon... • Answered on Jan 26, 2015

Primary charge failure .broken wire or not seated or arching to the grid.

Canon... • Answered on Jan 06, 2015

Check the connection from Fiery to reader controller PCB, located on the left side of the machine, just beside the TCP /IP port connection.

Canon... • Answered on Aug 10, 2014

Not finding what you are looking for?
Canon imageRUNNER 8500 Copier Logo

291 questions posted

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2351 Answers

Cindy Wells

Level 3 Expert

6281 Answers


Level 3 Expert

5720 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Canon Office Equipment & Supplies

  • Canon Office Equipment & Supplies

Most Popular Question

e000100 0000

  • Office Equipment & Supplies