20 Most Recent Canon NP 7130 Black and White Copier - Page 5 Questions & Answers

Yes. Open the copier up (push the gray button on the left side) then grab the installed cartridge and turn it clockwise til it meets a mark (they are triangles i believe) then you should be able to pull it towards you.Careful thou, you might get little dirty! for installing the new one just do the same thing but on reverse gear :P (or read the instructions on the cartridge box, ok i needed to say it; my bad)

The "waste basket" is to indicate that the waste toner area in the drum cartridge is full. If the copy quality is still ok you may be able to empty the waste by removing the drum cartridge from the machine and removing the opaque piece from the left side and dumping it out. BE CAREFUL this can be very very messy. toner is a very fine powder and will get all over the place if caution is not used. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/charles_45d8d6c78cd9f0b6

see if you have fax line(conect a telefone in the line to see if you have tone) or if the cable is conected.

try to change cartridge.

check your scanning lamp

Control panel definitely needs replacement. Based on the age of the unit and the cost (at least $350) of the repair, I would recomend replacement.

There really isn't enough information given to give a proper solution. This copier has the drum light come on steady or flashing to indicate the waste toner needs to be removed. I don't know if you're a technician or not but lay people have emptied the toner cartridge instead of removing the drum, removing the cap on top of the drum, emptying the waste toner , replacing the cap on the drum, then putting the drum back into the copier. I've never had a copier keep the drum light on after doing this.

Let me know if you need more help.

ur waste toner can is filled up. open & pure waste away, close and power.

This is your drum unit or transfer unit that must be replaced.In what area are you?

Yes,there is a arm that have to slide left to close the upper body.If the toner is in place you can close it slowly,with your finger you can guide that arm in the correct position.It will work untill you can get a technician to fix that for you.The technician have to strip the controll panel and boad to get to that locking device.

first try to look for the drum if it scratch no matter the distance btn lines
then if the drum is ok. look and adjust the position of the lens to home position.

try to clean the upper roller on heating section the final stage of the machines if the image is seen to be of the first objected copy this solution is only if you observed that the image of the previus object (source paper) is printed on the next copy or it repeats printing the lines.

and if it so replace or fix the new oil roler in heater unit.good luck vote me pls

try also to change or to service the corona units both the upper corona in the drum unit and the the transfer corona assembly unit down the drum. ok try your best.

ok so many things can couse this problem.

if it is total dark black and the scan light is there try to trace
1.too old the exposure lamp so that it brights low
2 the mirror on the scanning assembly may be one is missplaced eccidental or brocken.
3. the blockage of light by black pastics cover infront the lens
4. the heavy tonesof tonner powder is contacting the inner most mirror in optics section
5. the died preexposure lamp or its suply voltage is missing
6. the dc control board is mulfunction
7.the reflector mirror just at the scan lamp
8.excessive toner suply bias voltage biasing the toner catridge unit
9 too old the exposure lamp

tyr look on these and if it solve the problem pls vote me and if still the problem exsist let check another things i wish you success.

you are absolutly right. It needs toner. That symbol is the universal symbol for toner. ( dont ask me how they came up with that but its true.)

The reason the copier runs on when you turn it off and on is because it thinks you may have added toner and is trying to auger toner out of the cartridge into the machine. After a time it gives up and assumes the cartridge is empty..

If there wasn't wrinkling before the guide was changed, check for alaingment of the guide and any minor obstructions. Also, check the condition of the fuser rollers especially the lower pressure roller. Check for wear and the clear sleeve "gathering up", (if applicable. Did you do anything to change the pressure of the roller?

MM85

With toner being dropped I would take a close look at the cleaning unit next to the drum. Sometimes they become clogged or wear out. Inside the machine, can you see toner that has spilled or piled up? If so that is an indication of a faulty cleaning unit.

MM85

The Unit where you've put the toner cartridge could be to far from the drum. Make sure your developer unit (unit where you've put the cartridge in) is locked in place.

Most likely when you make a copy you don't see the light scanning the paper, you can try this with the lid open to make sure. the Sacnning lamp is blown, need to replace

clean the scanner glass. There is probably a tiny dot thats the culprit.