20 Most Recent JVC KD-G200 CD Player - Page 3 Questions & Answers

works fine cannot set clock

try going direct to jvc and you should get one,if not look for a faulty player with good front

If anyone knows how to fix this without taking it apart, I'd sure like to know!

Sometime something mechanical hangs up and once you take off the cover, careful examination and the gentle nudge or two can reveal it. Once the trapped CD is removed, the player works ok.

Other times it is a symptom of a more serious mechanical or electrical failure necessitating expert repairs.

Good luck!

Hi,
You can try the following steps
Setting the clock
1 Press and hold SEL (select) for more
than 2 seconds.
“DEMO,” “CLOCK H,” “CLOCK M,” “DIMMER,”
or “AMP GAIN” appears on the display.
2 Set the hour.
1 Select “CLOCK H” (hour) if not shown on
the display.
2 Adjust the hour.
1 2
3 Set the minute.
1 Select “CLOCK M” (minute).
2 Adjust the minute.
1 2
4 Finish the setting.
To check the current clock time or change the
display mode
Press DISP (display) repeatedly.
Each time you press the button, the
display changes as follows:
• During tuner operation:
• During CD operation:
• During power off:
The power turns on and the clock time is
shown for 5 seconds, then the power turns off.

Thanks for using Fixya
Proton

Hello jmartinatl,

The color codes for your receiver is here.

Just match the function of each wire the the appropriate wire on your vehicle. Or better yet, purchase a vehicle specific aftermarket wiring harness that plugs into the vehicle wiring.

Hope this helps.

Check all off your car electric system ... may be it's a short circuit or damage...

Check to make sure the antenna wire is attached to the back of the radio. Also there should be a source button that switches to 3 different preset settings. Try using this. If there is still a problem, let me know.

To set the clock on the JVC KD-G200 see here.

http://www.fixya.com/support/p187738-jvc_kd_g200_cd_player/manual-17158/page-9

CLICK HERE

THanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

I'm currently having the same problem. Take the face plate off. Use a pin to reset the stereo. It'll probably stop working again, but at least you'll be able to get your cd out and take it somewhere to have the stereo fixed or replace. (STAY AWAY FROM JVC!)

hold in select button for over 2 seconds it will change from tone settings to another menu then rotate knob CW to clock H or M press in and use knob to set.

For the JVC KD-G200 look here for instructions on how to set the clock...

http://www.fixya.com/support/p187738-jvc_kd_g200_cd_player/manual-17158/page-9

sounds like u got a bad unit if only certain things get power then it sounds like an internal problem

usually you would turn off the unit and hold the menu button for a fre seconds that will bring up a whole new set of options just scan through them and u should see adjust clock

Have you checked the fuse-box to make sure that you didn't blow the fuse for the radio? Also try removing the radio and checking the wiring to ensure that it is tight. There is also a fuse on the back of most radios to check!!

could have blown the speakers or if there sub woofers ran off an amp that might be your problem as far as the cause it could be something as simple as a loose ground or some wire that is getting power grounding out on a piece of metal somewhere i would double check all of your connections

Bump

I would suggest checking the accessory (red wire), the yellow is a constant feed from the battery, which will allow the clock to be displayed no matter what. The accessory wire is what is used to turn on the cd player. You may need to restrip the red wire and check the lead going to the red wire with a test light to make sure it is getting a voltage light.

If there is no power button, find the source button press + hold till it turns off. hope this helps!

Both times that a cd has become stuck in the player I simultaneously pushed the power and eject buttons. I came across this solution in the owner's manual and it worked perfectly both times I have had to do it.