20 Most Recent
JVC XL-MC2000 200-Disc CD Changer Questions & Answers
The cd player only turns on. it will not play or
I was able to clear code 15 but still do not know text of the code. I opened cover by removing 7 screws after unplugging and waiting awhile for any charge to dissapate. Then to remove the cover tilt it upwards almost vertical till you can remove it. Next felt around with my finger near and under the mechanism. I heard a slight click which i hoped was something realigning. I then put the cover back on, hooked it up and it started working again. I got lucky. YMMV
Jvc mc200bk - won't play
I hope that your model is a Refurbished JVC XL MC2000 - CD CHANGER XL-MC200BK/AUDIO COMPONENT.
What appears to be a malfunction may not always be serious and can easily be corrected. The table below describes some typical problems and their remedies. Check them before calling your JVC dealer.
- The built-in microcomputer is not properly
Disconnect the AC power cord and connect functioning due to static electricity or other disturbance. Put the plug back & try to turn it on
it again.
Some other points which should be checked before any repairs are:
The CD is not loaded. Load the disc.The CD is not placed in the slot with its Reload the disc correctly.
label on the left side.
A disc has been placed outside of the Specify the slot number and open the disc
loading area. storage door. Then close the door.
The CD is damaged. Replace the disc with a new one.
The AC power cord is disconnected. Connect the cord securely.
The audio cord is disconnected. Connect the cord securely.
Hope this helps................................................sodeep
.
Cd player skipping
The DVD transport rides on chrome rails. These get dust and stuff on them and wont allow the optics to track.
If you dare, open the unit UNPLUGGED from the AC.
See if you can get at those rails easily. clean with WD40 on a swab. clean with a new swab . then a couple drops of mystery oil on a swab and run down the rails over and under.
You must be VERY gentle if you clean the lens with isopropyl
CD CHARNGER PROBLEM
if your machine had never given that problem then the problem is in the microchip which needs to replace.good luck.
I have a JVC RX-501 reciver and 2 speakers Sony(200W). I start the reciver and After 3-4 seconds it S make a sound like" bun bun " that S all... After 1-2 minute again..
The sound you're hearing could be due to a variety of reasons, such as a loose connection, a malfunctioning component, or a power issue. Here are some steps you can take to troubleshoot the issue:
Check the speaker connections: Ensure that the speaker wires are properly connected to the receiver and the speakers. Make sure that the positive and negative terminals are correctly aligned. You can also try disconnecting and reconnecting the wires to ensure a secure connection.
Check the power source: Ensure that the receiver is plugged into a working power outlet and that the power cord is securely connected to the receiver. You can also try plugging the receiver into a different power outlet to see if that resolves the issue.
Check the volume level: Ensure that the volume level on the receiver is not set too high. High volume levels can cause distortion and other issues.
Reset the receiver: Try resetting the receiver to its default settings. To do this, turn off the receiver and unplug it from the power source. Wait for a few minutes, then plug the receiver back in and turn it on.
If these suggestion don't help, you may have to seek professional repair.
2/2/2024 9:08:57 PM •
JVC Audio...
•
Answered
on Feb 02, 2024
1997 JVC RC-X270 does not read CDs
A bit of basic knowledge is required first;
Insert CD, the first thing the processor expects is to scheive Focus.
When Focus is acheived, the Spindle Motor will turn.
Either the Laser cannot Focus or there is an issues with the Spindle Motor.
Which is it ... if you know, then you will know which part or board has the issue.
1/29/2024 6:36:28 PM •
JVC Audio...
•
Answered
on Jan 29, 2024
Not finding what you are looking for?