20 Most Recent JVC XL-MV303 CD Player - Page 2 Questions & Answers

CD players don't drive speakers. Get an amp or receiver.

get a new one problem solved

Hi,

Please check the links bellow to have a detailed idea to diagnose your problem:

http://inquirer.philly.com/newsroom/faq/pages/fdb7df9-30.html

http://www.kuro5hin.org/story/2004/3/24/45212/6874

Please accept the solution if it's helpful. Do get back to us for any further query.

Thanks for contacting fixya.com

I would not know where to get it repaired but I can tell you how to open the CD tray. There is always a hole in the tray. Please insert a pin into it and when you feel the pin has encountered resistance, press a little more and the tray will click open.

Vocal masking and Vocal replace how do you jvc mv 303 karaoke player

Sounds like you have a bad set of jacks. This typically occurs when the female ports on an electronic device begin to fail. The inside of these audio and video ports have a contact pin that the male connector comes in contact with when inserted into the female port. A little adjustment of the female pin connection will usually do the trick. You may also want to check the solder joints or connections.Sometimes they begin to break and lose contact.
Hope this was helpful. Good luck.

XL-MV303?

Visit http://www.jvc.com/

or

http://support.jvc.com/consumer/support/index.jsp

Good luck.

Do you have one for sale? I am looking for one I bought a new one for $300

You have either of these problems:
faulty speakers,wiring connection or if none of these then you have an IC blown up inside the unit.Test for any audio from other outputs 1 IC may be responsible for front audio and this may work..these varies from system to system.Hope this helps.

Bring it on the service center, color control IC causes this problem

try the switch in the back. move it to the left.

I had the same problem.. had to change my video cord that goes from player to TV

Please connect any other video source on same AV input of TV just to make sure that TV AV input is fine.
Also hook your dvd player to another TV just to confirm that dvd player has problem or there is some thing else.
Once got sure that dvd player is defective, let me know exact model number of player to find out info.
Thanks.

have got it all figured out.. thank you for your help/.. my video cord that goes from player to TV didn't work on this unit but does on my old emerson. But with your help I figured it out.
Thanks,
Patti

Do you still need the manual..........I have some......you're welcome to one....

Paul

[email protected]

It does have an aux input with two levels but this isn't suitable for a turntable. A suitable input should have RIAA correction with a sensitivity of just a few millivolts for a magnetic cartridge. Instruction manual can be found on the link below... http://resources.jvc.com/Resources/00/00/90/LVT1519-001C.pdf

Here is the user manual; https://www.manualslib.com/products/Jvc-Th-A75r-252593.html

The sound you're hearing could be due to a variety of reasons, such as a loose connection, a malfunctioning component, or a power issue. Here are some steps you can take to troubleshoot the issue: Check the speaker connections: Ensure that the speaker wires are properly connected to the receiver and the speakers. Make sure that the positive and negative terminals are correctly aligned. You can also try disconnecting and reconnecting the wires to ensure a secure connection. Check the power source: Ensure that the receiver is plugged into a working power outlet and that the power cord is securely connected to the receiver. You can also try plugging the receiver into a different power outlet to see if that resolves the issue. Check the volume level: Ensure that the volume level on the receiver is not set too high. High volume levels can cause distortion and other issues. Reset the receiver: Try resetting the receiver to its default settings. To do this, turn off the receiver and unplug it from the power source. Wait for a few minutes, then plug the receiver back in and turn it on. If these suggestion don't help, you may have to seek professional repair.

A bit of basic knowledge is required first; Insert CD, the first thing the processor expects is to scheive Focus. When Focus is acheived, the Spindle Motor will turn. Either the Laser cannot Focus or there is an issues with the Spindle Motor. Which is it ... if you know, then you will know which part or board has the issue.