20 Most Recent JVC RX-1028V Receiver - Page 8 Questions & Answers

So if you're trying to amplify the sound coming out of your TV to an amplifier you need to connect the output on the back of your TV on the receiver to the end audio input on the back of your receiver you might need different types of connections on each end but as long as you take the output on the TV and input it into your receiver your receiver will amplify the sound another way you could do it is to go inside the TV and connect two wires off of each of the two wires of each speaker leaving the internal speakers connected and then plug them in to the audio inputs on your receiver also if you're using one of the audio outputs on TV make sure you go into the menu and tell it you're using external speakers Good Luck Chuck

roflmao - I just upgraded my phone from a samsung galaxy s4 and the AT&T tech laughed as he asked me how i managed to keep mine working so long. you likely need a new phone dude. the easy solution: get a new one.

Sub woofers are basically mono amps. It's likely that either a fuse has gone, on the sub, due to the blown caps. Or more likely the main power amp device of the device blew the caps. I suspect if you replace the IC or transistor(s) on the heatsink then the device will come back to life.

http://www.usersmanualguide.com/

Hi, Here is a link to the JVC support site where you can download a manual in PDF format to show you how to hook up you system. resources.jvc.com/Resources/00/00/93/GVT0150-001D.pdf

The click is a relay. The 12 position is obviously past the max you should be applying. Keep it below that and you should be fine. Quite often the 12 or 1 position is the max output for a receiver. It depends on a lot of different factors but in your setup 12 is It.

Hello here is a tip.maybe you have already tried this but on the back you have the speakers and a pair of red and black switches, you have to put the wires into the holes on the TOP (not the sides) of the little box on the back...then once you have put the wires in flick the flaps UP :) JVC UX LP5 Micro Desktop Stereo System JR com

What model of JVC? Portable, table-top hi-fi type, model number? If case-type with a bezel, which ejects, maybe the ejection mechanism is faulty. There's at least one article in TIPS for this. Otherwise if it has a pinhole at the front, bezel type, shove a paper-clip firmly in to manually eject.

Ideally, you need an FM antenna, which is usually a folded dipole loop, looking like a 'T' made of parallel conductor. The input impendance, symbol Z, is usually 50 ohms, so the F 750 may be F Z50 with bottom of Z not visible. F=Frequency modulated input Z=Impedance 50=50 ohms impedance The number '750' makes no sense, as the FM broadcast band frequency of 88-108 MHz is way below 750MHz (UHF), and impedance at 50R is well under 750 ohms. Tip: Although a proper FM antenna is recommended, in good reception areas, such as near a city, a single insulated wire stuck into one 2-pin FM socket or center-pin of a coax FM socket can give reasonable reception.

Like most receivers it will probably have settings for the sound output. Once you find this it will be just a matter of switching the system over to Dolby signals. If you find that it already set like that, try switching the DVD or blue ray player you are using or whatever source, using their sound settings on them. So that both devices are sending and detecting Dolby signals. If both devices are set correctly then there probably will be a fault in the decoder of the JVC.

hi frances, go to this link and you might find your manual. manual jvc receiver amplifier model no AX R97BK Google Search

see if this link helps you out. Tips for Repairing Your Home Turntable .. or this one.. JVC AL E31 Turntable doesn spin automatically Google Search

On e-bay there are lists, maybe they have it