20 Most Recent Mpio FL300 MP3 Player Questions & Answers

now they have the fl300 and i cannot tell for sure what type of usb connection it has. As it shows on the website that there is a special usb connector the goes from usb-1/4" audio jack. But it also says it has mini usb connection. The device is listed as plug and play so if you plug it into your computer with the proper connection it will automatically connect and allow you transfer files. if it does not pop up then it is most likely the product is damaged. here is link to there website. The website is only in Spanish. http://es.mpio.com/product/productview_fl.html?view=a

do you have your USB cable? keep it connected to your computer that helps you to transfer files and charge it. device ill tell you when it's fully charged actually there is no charger for it.
if you need to read about it here is a link:
http://www.mpio.com/product/productview_fl350.html

if it works for you don't forget to rate me

thx

Invalid MBR = Invalid Master Boot Record.
This means that your player Flash Memory drive is corrupted and unfortunately may need to be reformatted if you cannot repair it using some Disk drive or Flash drive utility.
You can try to use 'Properties -> Tools -> Error Checking -> Check now' to fix the issue.
If you have a backup of the music on your player, I would simply use Windows Explorer and FORMAT it using FAT32.
Hope it helps.

my mpio FL300 can't conected to my computer,because i've been format it.how to solve this problem?thx.(if ful)

Somthings wrong with the USB cable or the USB port

either you got a faulty surface mount regulator IC or you got a corrupted flash memory. Try pressing play button, then alternately press volume down (-) and Rewind (<<) buttons. When the "FORMAT? Press Menu" appears, press MENU BUTTON. A LOW LEVEL FORMAT will be in progress. When it's done, reload firmware recovery using MPIO Utility. If however you nothing appears on the screen afteryou pushed the play, rewind, and minus buttons,or still it doesn't power up, you've got a faulty regulator IC. It is the five pin chip colored black with the markings "PHK" (use a magnifying lens to confirm) located on the left besides the battery connector (facing up, with the earphone jack on the top). If you had micro soldering skills, then you can remove the chip and replace, if you can find a replacement...

I have the same problem. I can store things in it but can't see the screen. the LED seems to have died first the light went out then it just died.. This is the 3rd Mpio FL300 that did that to me. I returned the 2 others before the warranty was out but this time it's to late. how do we fix this problem in other words how do I get the led to work????????

ok what charge setting is it on? if its on the MTP setting hold the "MENU" down until a message apears that says "reconnect the mg100 to change the mode" then it should work. if not then i guess i wasnt verry helpful and im sorry

Either the device is bad, the pc port is bad, or the software is faulty. Try connecting to different usb port, then a usb port on a different pc with a compatible os. If still not recognized, then there is physical damage to player.

Try this: disconnect the player from the computer, turn it off, hold in the volume + button, and reconnect the player to the computer while holding the volume + button in. Keep holding the volume + button for an additional 5-50 seconds. Windows should eventually go into recovery mode and revive the player- it will pop up a window that says Found New Hardware Wizard.

If the display is working, you have audio. Check your amplifier. 1300Watt adaptor ... This unit draws a very low power and that is not needed.

1. Power Off: Turn off the device.
2. Jumper Configuration: Locate the jumper labeled "S16" on the device. Initially, it should be connected to pins 2 and 3.
3. Power On (Alarm+All LEDs Flashing): Turn the device back on. You'll see the alarm LED and all other LEDs flashing.
4. Power Off Again: Turn off the device once more.
5. Jumper Adjustment: Change the jumper configuration from pins 2 and 3 to pins 1 and 2.
6. Finished: Your Porpo YH-2000 is now set to the desired angular unit mode.

If you encounter any issues, you can press the reset switch on the back of the device to reinitialize it.

this model SA rather than SC seems to be a Middle East model. The SC version doesn't have DAB. https://www.google.com/search?q=panasonic+sa-pm250+instruction+manual ..