Polaroid FLM-2011 Television - Answered Questions & Fixed issues


Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician. http://electronicshelponline.blogspot.com/

Polaroid... • Answered on Oct 20, 2016 • 49 views


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Polaroid... • Answered on Mar 10, 2016 • 44 views


this happens to my tv as well it simply will just shut off and turn itself back on and then shut itself off every 2 - 3 minutes...can someone help??

Polaroid... • Answered on Nov 12, 2014 • 827 views


reset with cable box doesn't work?.

Polaroid... • Answered on Oct 30, 2012 • 44 views


Going to have to use a volt meter and follow the voltage inside the set.Fairly straight path---AC comes into set past the fuse--at some point if it vanishes before the voltage is rectified (changed from AC to DC) something is open---a resistor or two should be there and may be opened. After it is changed to DC there are a number of other protection and blocking parts.The change from AC to DC usually involves a bridge rectifier.These are fairly basic tests but if you cannot do them time for a technician or a shop to look at the unit.There are a lot of fail safe's in place to protect a set from this type of damage but they are parts designed to destroy themselves in the process.

Polaroid... • Answered on Jun 11, 2012 • 145 views


Hello
Get into this link where you can download the user manual of your poloroid FLM 2011. It is an adobe acrobat document. You must have Adobe Reader installed in your system to read it. Reader can be downloaded and installed from Adobe.com site for absolutely free. OK
www.polaroidsupport.com/polaroid/docs/FLM-2011-ServiceManual.pdf

Polaroid... • Answered on Jun 27, 2011 • 545 views


well the child block is on u just have to get a remote that responds to the tv and remove it it works because my TV had the same problem

Polaroid... • Answered on Feb 20, 2011 • 169 views


It sounds like you need a new power supply, You and find one on amazon around $14 too $18 dollars maybe less, if that not your issue then it's going to be a fuse but since you can see the light it should be the power supply.

Polaroid... • Answered on Jan 25, 2011 • 59 views


Check on the back of the set for the fan. Make sure it's working. You can clean it off with Dust Off. Sounds like it's overheating.

Polaroid... • Answered on Jan 14, 2011 • 38 views


check you tube, they have video on how to fix

Polaroid... • Answered on Jan 08, 2011 • 22 views


all you need to do is google the remote type and number and find Polaroid codes

Polaroid... • Answered on Dec 16, 2010 • 393 views


Its either the LCD panel that's bad or the LCD T-Con board needs repair/replacing.....
http://tvtechwork.webs.com/

Polaroid... • Answered on Nov 13, 2010 • 46 views


I have not repaired this particular model. But,let me say this first. When you are describing, power out , are you referring to the TV or an actual power outing in the home? None the less the biggest problem with the polaroid flat TVs are the filter capacitors. I have repaired many versions of these and that seems to be possible here. I found the most capacitors replace were in the actual signal board. This is the board with the RCA connections and RF (cable TV connection) connector. I believe I replaced about fifteen of these in the signal board. The power supply board had two caps replaced. This is very time consuming and takes great effort not to destroy the circuit traces. One other thing, If this model has an external power supply (transformer connected to power cord), I would certainly look at this as the first problem. Remember, I have not repaired this particular model. This information is very good and most reliable. Take this note to a TV tech near you and have him quote you his solution and price. You have confidence to take with you. Thanks for asking and show a few hands of support!

Polaroid... • Answered on Oct 25, 2010 • 50 views


Hi,

In Child Lock On mode, the buttons on the TV do not work. A prompt "Panel buttons are being locked" will be displayed. However, the remote control buttons will still function. When the TV is on and the Child Lock is on, a prompt "Locked, power off after 6s" will appear. Use the remote
control to control the TV.
Otherwise, the TV will automatically enter into Standby mode.
For program lock Input the default password of 1235.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Polaroid... • Answered on Sep 26, 2010 • 326 views


Hi,

First check that any muting control is not activated. This might be a button on the remote or set itself. If you have a headphone jack, it may have dirty contacts as plugging in a headphone usually mutes the speaker.
If the set is mono or only one channel of a stereo set is out, then check for bad connections to the loudspeaker. Test the loudspeaker by disconnecting one of the wires (with the power off!) and measuring its resistance with an ohmmeter (it should be less than 100 ohms - probably less than 8 ohms). Or momentarily touch a 1.5 volt battery to the speaker terminals - you should get a click or pop from the speaker.

Next, trace back from the speaker output terminals to the circuit board and look for bad solder connections or a loose or dirty connector.

If these tests do not reveal anything, you probably need a scope (or audio signal tracer) and schematic. Or at least the part number off of the chip. Is the final amp a chip also or just a transistor? Have you tested the transistor? If there is little or no buzz from the speaker, that would indicate a problem fairly near the output. If the tuner/if were bad, I would expect some noise/humm pickup from the low level audio stages. Get the part number off of the chip. If it is in a socket, check the contacts for corrosion or looseness.
Hope this help in solving the problem....

Polaroid... • Answered on Sep 05, 2010 • 34 views


The tv power supply board have problems.Tries websites like Shojimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.It will solved this problems.

Polaroid... • Answered on Jul 12, 2010 • 97 views


I have the same problem. Brought it into TV repair shop, and it worked fine. He believes it may be my power adapter. Shopping for a new one. Hope that does the trick.

Polaroid... • Answered on May 28, 2010 • 126 views


Ur tv is missing one color.Might be the incomming signal colax cable is damage or ur tv tuner board is dead.Take ur tv to another location,hook up to another incomming colax signal cable have the same result,the Tuner board is dead.Tries Shopjimmy.com,Ebay.com to buy a refurbish Tuner board for the replacement.

Polaroid... • Answered on Dec 17, 2010 • 587 views

Not finding what you are looking for?
Polaroid FLM-2011 Television Logo

Popular Tags

107 questions posted

Ask a Question

Usually answered in minutes!

Top Polaroid Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76587 Answers

Cindy Wells

Level 3 Expert

6262 Answers

Paul Bade

Level 3 Expert

1688 Answers

Are you a Polaroid Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...