Top 20 Haier HL24XLE2 LCD TV Questions & Answers

T con pcb might be faulty or the screen.

Check its back-light inverter board. Replace it if found faulty. If you wish to get some details, check the site linked here. Pull up older posts. Check the site in 'Mosaic' view. It will make search easy. http://electronicshelponline.blogspot.com/

you can program the channel manually, just press the menu button in the tv panel. select preset and then manual fine tuning to tuned every channel you want to watch and then save it.to make a manual fine tuning, press manual then select channel you want to tuned and then press vol. up/down button to search right frequency channel.do this process in every channel you want to tuned. hope this can help.

Try changing the input device to something you are sure, works such as a DVD player.Switch off TV manually, switch off power, remove plug and retry after 48 hours.If problem persists, please refer it to a qualified service technician.

May be you have a faulty video cable from your cable set-top box or your DVD player--try changing the cable to see if it fixes the problem.Also, is the video cable an HDMI cable or component (like RGB)? If it is a component cable, it may be they are connecting properly.

Good day!!!!That problem is usually cause of faulty capacitors on the power supply board..Just follow this instruction to fix your TV..1. Open the back cover of your TV.2. Look at the power supply board..Its normally connected to the power cord..3. After that,,try to look at the actual image of capacitors if it is bulged on the top so that you can easily determine the bad capacitors..4. After that,,try to replaced the bad capacitors using soldering iron and soldering lead..replaced the capacitors only with the same type ratings and value..5. Some of the capacitors not bulged so its better if have a capacitance meter

Tries tv and those pay boxes unplug,replug it back like about an hour later for the tv to do a resetting itself back to the factory setting.For those pay boxes to reboot and upgraded it softwares.Go into the tv menu go to Sound Setting go down do a resetting itself back to factory setting.By doing these steps tv have a great chance to get it audio back.If tv still have audio problems,than the main tv Tuner signal board have problems.Tv is under a year old.Call the Haier tv Corp.Take ur tv warrenty repair.

Informed customer to try emailing Haier for product support since she can not call the toll free number, also suggested that she unplug the television for about 5 minutes to allow the set to rest itself. Then plug the set back in and try turning on to see if this cleared the symptoms..

Try setting the TV from Component (YPbPr) to VGA (RGB).

you have to go to your dealer to order a new one//

no no no no you cant..

Are you using a cable or satellite box? If so you can connect the audio out jacks to the Surround Sound instead of the TV.

These are the setup codes for Haier: 0081 0216 0217 0157

Try reset TV using instructions given on page 13 of manual.See troubleshooting section on page 16.User manual Haier L42B1180 (English - 19 pages)See page 43 of service manual (roubleshooting)https://www.manualslib.com/manual/1065697/Haier-L42b1180.html?page=44#manual

One of the most common issues is that the circuit breaker or power breaker of your TV might be faulty. You can check if they are working fine for this issue. There can be simple causes of this problem too such as the plug or remote control defects. If the above solutions do not work, you can try contacting Haier's service hotline and book an appointment to check your TV Sorry.

You should enter its service mode menu to do that. Visit these sites by a desktop computer and type in the model number of your set at the search window at the right side of the site to reach it very fast. Mobile view have no search box. https://electronicshelponline.blogspot.com/ https://elektrotricks.blogspot.com/ https://electrohelponline.blogspot.com/

Hi, please remove all accessories from your tv and monitor it to see if it runs into it's glitches again. Please also remember if you purchase a new remote when this issue started happening or did you start using direct tv ? You can also run a power cycle on the tv if this issue occurs again. Thank you.

You can try unplugging the TV for a bit to see if that resets it. Next check if the TV was set to use external speakers by accident. Finally, try a factory reset. Please add a comment with the model of the Haier TV for directions for checking the audio output menu and factory reset. I hope this helps. Cindy Wells (I had a different TV from a different brand that had no external audio port. It would sometimes lose audio on one channel or several channels. Unplugging the TV solved the problem; the factory reset option in the TV menu didn't resolve the issue.)

Most air conditioners need water removed, not added. They act as dehumidifiers as they change the air temperature. What model air conditioner do you have? The Haier HPRD12XH5 has a blinking red LED with a triangle symbol to indicate the unit is flooded. Air conditioners can also fail if there is a coolant leak or the room is too cool. If the removed water freezes in the air conditioner, it can damage the fan and cause the motor to overheat. The air cooling systems that need water added are "swamp coolers". That's the term I learned for the old-fashioned fan + ice/water cooling systems that work well in low-humidity environments. They'll make the area feel hotter in high humidity conditions. I hope this helps. Please add a comment with the model of your unit for further information. Cindy Wells

Normally you need a remote to access the Input Source. All televisions need a remote! If you can access Input, just scroll through them one by one until you get the signal. Replacement remotes are typically $12 to $20. Some Haier as $31. Add your model number after the word 'Haier'. https://www.google.com/search?q=haier+tv+replacement+remote ..