20 Most Recent Tascam Pocketstudio 5 MP3 Player - Page 9 Questions & Answers

A Technician usually has to get a tape out of a machine when this happens. In radio when I was Chief Engineer for several stations in Chicago I would send my defective decks to Russ at New Jersey Factory Service in Emerson NJ. He knows how to fix these units.New Jersey Factory Service, Inc.16 Chestnut Avenue Suite 103 BEmerson,New Jersey 07630201-967-0060Fax 201-967-0062Mon- Thurs 8-4 Closed Fri Sat by appt.

Send me a model number and a request by regular E mail to [email protected] and I will see what I have but in many cases depending on what you are working with the motor may need replacing.

Only one place- Teac in California.It is better to just fix the one you have unless it is smashed.I have worked on these decks many times and have not had to replace any boards so far.

Owner-manuals.com can sell you one in Pdf file. If you want paper which is always the best to have for service manuals.contact Rick at stereomanuals.com This is where I get my service manuals- he has owners manuals too.

If he wants you to get parts then I would suggest you get a different Technician. Why would any Technician want to go to the trouble and risk of the customer getting the wrong belt. You can get a set of belts from Marrs Communications for that model.http://marrscommunications.com/tascam-cassette-kits

This type of model does not have an eject button as the deck is designed so that when the head is retracted as in stop mode you simply pick up the door and pick the tape out of the well. This is pretty much the same in all the lower end Porta Studio models.

I'm not familiar with the Tascam DP-01 but many multi-track recorders don't commit effects to the track until the mixdown phase. The thinking being that you cannot eliminate a "bad choice" effect once it's down to tape (old school term) and so they allow adding the audio tweaks at the final stages of recording. Here they hope you can appreciate the entire mix and then decide what sweetners to add.

alors c'est quoi la solution car moi pareil !!!

Hi Julian,There is a lot that can go wrong with these miniature helical scan systems. When I had units like that I packed them off to Russ at New Jersey Factory Service and they were restored. I am not sure about parts like drums at this point but Russ is your best chance to get it working again. He has corrected CDRW and DAT as well as just about anything Tascam makes and he even fixed some Sony units too. I know him as the counterpart to the Chicago Factory Service facility when it was open. He was the Manager in New Jersey then.New Jersey Factory Service, Inc.16 Chestnut Avenue Suite 103 BEmerson,New Jersey 07630201-967-0060Fax 201-967-0062Mon- Wed 8-4 Thurs 8-3(July-Aug) Closed Fri Sat by appt.

It is hard to guess what is causing this but for all of the gain to be reduced like that either the deck has seen some really high input signal in the past that blew out some amplifiers or that there is a power supply component that has taken the input electronics down.I suspect that you will need to have a Technician look at it. If you are near Chicago, I may be your answer, I have been working with these Teac units for 40 years and was a Lead Tech at Chicago Factory Service in Arlington Heights.I can be reached at [email protected] you are far off- I have other people that can do the job one in New Jersey and a few others.

Some players are programmed to read store bought cd's only.

You have not mentioned the model. Hope you have checked the belt and the motor that drives teh main capstain and the reel drives. If this does not work then replace and proceed. Also the pinch roller could be defective and not holding pressure to the spindle. Check the roller for hardening of the rubbers. replace if this is faulty. I hope with the set loaded with a tape you can find which drive is not spinning to take up. This should be able to confirm you with the right section. Hope this helps. Good day

Have a look at this site:
http://www.angelfire.com/electronic2/vintagetx/Tascam-42.html

This docs dont for free, but could help this link:
- ascam-22-4-reel-to-reel-manual-free-pdf-pdf
- TASCAM_22_4_REEL_to_Reel_SERVICE_Manual

Hope helps.

You should be able to find a manual for it, many free online sources. Yes you can use it for r-t-r playback to transfer to CD's. One in good condition will typically go for $300-$400.