Top 20 Humax Hdr-Fox T2 500Gb Freeview Hd Digital Tv Recorder Questions & Answers

Having looked at the manual it doesn't look like there is any option to change it to that. It will simply list them in the order they were recorded. With the last first.

If you wish to get some details; check the site linked here. Pull up older posts.. http://electro-medical.blogspot.com/

http://www.humaxdigital.com/uk/rcucodelist.php

You may have a loose wire or one that's not making good connection. unplug all wires going to hard drive, then reconnect them. Also make sure the plugs to the motherboard is secure. I have this same problem with my pc from time to time.

Nope I had to disconnect it from the mains Spent too long trying to catch the right box to stop the flashing screen

Place it where there's good ventilation.

Get a new one.

Are you sure it HAS formatted and the 0Gb tells you have no recordings!

You possibly have erroneously selected "delete all". I once fell for that!

This device has a fan that will turn on when the temperature of the internal hard drive reaches a certain level. The problem may be due to a faulty sensor, fan or both. here's a forum for this hardware that may be of help: http://hummy.tv/forum/forums/hdr-fox-t2-freeview-recorder.13/

USB memories formatted NTFS will read XviD videos. Ext3 or FAT formatted will copy or read XviD. MPEG4 is not supported but your TV may be able to show them directly via its USB PORT.

That is what always happens when something breaks... It would help if you had more info like was there a electrical storm, does everything else work, do the lights light up... I will say this; Most electrical appliance failures are due to no power. As in the switch in the surge protector was turned off when vacuuming the area, etc. So, check all the connections to the wall and then if these are good, by good I mean you replaced them with known working extensions and check the little ground fault button in every outlet too... then get back with more info.

Try both the device control and the cable control. Each should have a menu for this screen problem.

If it has an ethernet cable connection, get a shielded one and connect to your modem.

Connect by Ethernet cable. If still buffering too often get a faster broadband.

Restore factory settings and go through setup step by step.

Tell us in detail what happens when you do what. The better you describe your situation the better we can help you.

Restore factory settings (if you can) and start from the beginning.

You did not mention model of remote control. You can download the required manual for your remote control from following link. Remote Control Code List ' HUMAX-United Kingdom (humaxdigital.com)

If your Humax 5000t is not finding HD channels during scanning, there could be a few potential reasons for this issue. Here are some troubleshooting steps you can try:

1. Check signal strength: HD channels may require a stronger signal compared to standard-definition channels. Make sure your antenna or cable connection is secure and properly aligned. You can also try repositioning the antenna or cable to improve the signal strength.
2. Perform a full rescan: Sometimes, a full rescan can help resolve channel detection issues. Go to the settings or menu of your Humax 5000t and find the option to perform a full rescan or channel search. This process may take some time, so be patient and allow it to complete.
3. Update the firmware: Outdated firmware can cause compatibility issues and affect channel scanning. Check if there is a firmware update available for your Humax 5000t. Refer to the manufacturer's website or user manual for instructions on how to update the firmware. Follow the recommended steps carefully to avoid any potential issues.
4. Verify broadcast standards: Ensure that your Humax 5000t is compatible with the broadcast standards used in your region. Different countries and regions may use different broadcast standards for HD channels. Check the specifications of your Humax device and confirm that it supports the specific HD broadcast standard used in your area.
5. Reset to factory settings: As a last resort, you can try resetting your Humax 5000t to factory settings. Keep in mind that this will erase all your saved settings and recordings, so make sure to back up any important data beforehand. Look for the reset option in the settings menu of your device and follow the on-screen instructions.

If none of these steps resolve the issue, it's advisable to contact Humax customer support for further assistance. They can provide specific troubleshooting guidance based on your model and help you resolve the problem with HD channel detection.