20 Most Recent Zenith C27A24T 27" TV - Page 3 Questions & Answers

What´s the control manufacturer?

1. Manually turn on the tv.
2. Hold code search button until the red light stays on.
3. Press and release TV button-the light should blink
4. Enter one of the following codes: Phillips Universal remote Codes-713 502 606 409 710 701 507 714 405 712 015 916 008 002 115 224 324 126 326 826 228 430 632 435 437 903 407 OneForAll Codes- 0017 0463 0178 009 With a valid code entry, the light should turn off.
5. Press channel up button. If the tv responds, the code worked.

If some functions (like mute or menu) dont do what they should, try a different code.


Good luck.

Try website like Remotes.com to buy the tv original remote.

Actually, if you have an old appliance cord (lamp,extension,etc). You may use any of these. Or if you want to spend a buck or two, see matelectronics.com, or MCM electronics.com. This shoul help you find what you are looking for. Thanks for asking and show all hands of support!

Check the Fuse and the Hori output Transistor.
You can ship Board for repair PTS 1-800-844-7871

Hi
Take it to a reputable repair person who will give you an honest estimate. This repair should be less than $120.00

Greetings - You need to have you DVD player hooked up to the video inputs - See below. Don't mind the mouse scratch out lines. The Device on the right represents your DVD player.




You then have to choose video as your source on the TV (not channel 3 or 4) using your remote - see below.


You should be good to go.

Enjoy your movies,

Mikeywaf

Make a fist with ur hand and bang on the tv bazel frame.The tv picture flickers back or bounces back to a normal picture.The tv have a vertical or a horizontal hold ics have coldsoldering joints and requiring resoldering.If u bang on the tv bazel frame picture don't flickers back or bounces back to a normal picture.The tv have a vertical or a horizontal hold ics are dead require changes those ics chips.If u don't have all the tools.Can't do a basic soldering work or able to changes those ics chips.Shop around for tv shops for estamate and repairing prices for repairing.

hit your TV lightly on left side or right side or on top & then observe ..........you will get normal picture or it comes & again it goes....if it is happening like that then following is the situation..........after 4 or 5 yrs in some TVs on main board (also on circuit board that is fixed to CRT TUBE ) at some soldering joints crack develops....then due to loose contact picture becomes small in size or disappears or rolls ( in your case )...........when we hit that lightly then those loose contacts joins temporarly & again picture appears for some time............so solution is ......TV main board should be observed carefully & most of the joints should be re-soldered.......only a good service engineer can do that........even after hitting TV lightly if there is no response then main board has to be checked completely........in your case iam sure it is loose connection problem.........joints should be re - soldered ...100% it works again................this problem cannot be solved by user unless user has idea about components( resisitors, transisitors, diodes,...etc) , have soldering iron , multimeter & other tools....................so contact good TV service engineer

Try to auto program the channels

There is one easy way to check this, if you have a dvd player or vcr handy and hook it up and test it, that would tell you if the Satellite is the problem "which it commonly is" or if it actually is the tv.

Hi Ronnie,
You may view Universal remote control code,click the link below.
http://oneidatel.com/support/dtv/entone-urc-plus.pdf.
Additional code : ZENITH Codes: 000/ 001/ 004/ 023/ 038/ 058/ 059/ 064/ 121/ 135/ 136/ 153
Hope I helped you.
Have a nice day!
Thanks for using Fixya.

Leave Comcast connected to Tv then Go to Menu and Change from Air To Cable Then run Auto Programming.

You can buy a new one for less than 200 bucks. I'd advise you do this. It sounds like you need a new
picture tube

I have a Zenith Tv Model C27A24T and a Universal Phillips remote..i need codes

Hello

Three digit remote codes for Zenith TV are:-

000/ 001/ 004/ 023/ 038/ 058/ 059/ 064/ 121/ 135/ 136/ 153/ 0016/ 0017/ 0092

Four digit remote codes for Zenith tv are:-

0121 0009 0050 0078 0091 0138 0059 0131 0038 0111 0134 0153 0064 0004 0135 0226 0227 0245 0247 0252 0266 0288 0310 0338 0358 0023 0058 0039 0001

You have to find out which code will suite your tv with patience. Proceedings are given below. Switch on and switch off the tv before trying each code.

Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

OK.

I had the same tv at my motel and wanted to hook up my Wii. Turning to Channel 999 worked.

Hello
I've only only one digit code with me. It is "0634". It is the remote code for Zenith HDSAT_420, HDSAT_520, HDSAT_1080. Sometimes this may work with your TV also.

Proceedings

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

*******************************************************************************************************************

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.