Zenith DVT412 System - Answered Questions & Fixed issues

All you have to do is connect an Optical or Coaxial cable from your Direct TV receiver to the same type of connection on your Zenith. Switch the unit to that input and you should be good to go. For more information, please visit my website at audioserviceclinic.com. Thank you.

Hi, Yes you can use most any wire you want as long as the size ( thickness ) of the wire is approximately the same. Also when connecting make sure to not have the wires touch ( can happen pretty easily especially if original wire ended in some sort of plug set up ) that about does it, I hope this was of some help-thanks for asking FixYa and good luck, Prodzilla.

this is a protection circuit.
When bypass mode then it means that something in the power supply module has failed and the unit then goes into protection mode to protect the board components.
Your surround sound need service from a qualified tech. No other remedy.

Have you tried swapping the scart lead ends around, this might work.

put a disc in the player and once it starts to play press stop, then press and hold the stop button for 5 seconds this will turn off the progressive scan feature.

just talked to LG Customer support and got them to send me a manual.

to turn off the progressive scan insert a disk and once it starts playing press stop, then press stop again and hold for 5 seconds this will turn off the progressive scan mode.

use nothing but RCA output and input to all equipment. you will need a video cables..its three cables seem/connected side by side together with all male jack at one end and to the another end. the cable are color coded; (you can get this wire from walmart or radio shack, staples and make sure you get at least 5-6 feet long cables) yellow is for video and red for right audio and white is for left audio. everything is color coded on your TV,VCR and your reciever, you cant really get it wrong on the color. fist take one of the yellow video cable to your your tv input and to your vcr output, next take the red and white audio cables and plug it in to your vcr output and to your receiver input. that should do the trick. any other question just ask and i will try to walk you through. good luck!

See if you can select audio channels from the audio control menu, and try different choices in there.

I just discovered this site because my remote just quit as well. Here is the direct link. http://www.partstore.com/Part/LG+Electronics+Incorporated/LG+Electronics%2fZenith/6710CDAL01C/New.aspx?ModelMfgName=LG+Electronics+Incorporated&ModelBrandName=LG+Electronics%2fZenith&ModelNumber=DVT412 Not bad price either.

thanks it help me very much 

how do I get the dvt41`2 to play audio from my tv

To everyone having sound trouble... there is a solution! First make sure your TV is OFF. Unplugg the 2 main cables going into the DVT 412 for 30 seconds. Then re-plugg them. Press down for a few seconds on all the BLACK tabs connecting the sound wires and release. Without a disc in the player... and the TV still OFF, turn the power on and immediatley hold the down the STOP button on the DVT412 for 5-10 seconds. Your picture, vocal and backround sound will return to normal. Feel free to make changes to the sound now! Happy tuning... GO STEELERS! LOL!

Sounds like the system switch is broken. They use a piece of spring steel thats bent up to provide a snapping action (its very small). After years of continuous pressing the metal fatigue fails and breaks so there is nothing to keep the contacts apart. The most common button you will see this is in the volume up because its used the most. It seems that people usually adjust their volume up in more steps than lowering the volume as their ears adjust to the levels plus people tend to push the volume up button harder than the volume down.. There are a couple things you can do when this switch goes bad. There is probably a button on there that you dont ever use or could live without (loudness perhaps). You can take the good switch off that button and replace the volume button with it. You can do this by either desoldering them or by popping the clip off the switch and replacing guts. I have found it much easier to desolder them however because the small pieces are difficult to manipulate. If you dont want to lose the function of another button, you can try matching the switch with one from an electronics supply place like digikey, or go to a repair shop and ask them to replace the button or sell you a good button out of a broken face. Good luck!

Without disc on the tray push the stop button for 5 seconds

Al parecer activaste la funcion progresive scan,trata con esto sin disco en la bandeja presiona la tecla stop por 6 segundos esto desactivara dicha funcion.
Que tengas suerte.

Try this without disc on the tray press the button stop for 5 seconds.Good luck

Hello Nibas,

You may have damaged the laser diode or one of the biasing components, you will need to take this to the shop to have it repaired. This is due to the fact that the laser output has to bee measured and you don't have the equipment to do that. This is not a case of resetting the DVD player which on this unit only covers if the unit is in progressive scan mode (how to reset from progressive scan). I know this is not what you may have wanted to hear but it is the truth. In any event you will have to take this unit to a repair shop.

I hope this helps,
Thank you,
Shuttle83

find the info/display key on the remote and press it,go down to the box that show head speckers it should show 2 ENG and CH2.
if not change it by pressing the down key then press ok key

wot inputs does ur tv and sound system have?

Go into the units system menu and change the unit to NTSC or PAL, depending on what country you live in. Good Luck