20 Most Recent Kyocera KM-1510 Copier Questions & Answers

enter the service mode by pressing 10871087 .there will be U000 then press 163 through keypad then press START button 4 times machine will restart .wola. check ur input voltage it is fluctuating

Kyocera KM-1510... | Answered on Feb 27, 2020

Code J00 is paper tractions error, either one of the traction wheel or one of the sensor is stuck or defective, often you need to take apart the printer to fix this.

Kyocera KM-1510... | Answered on Jan 29, 2020

press 1087 1087 than insert 163 than press start 4 time

Kyocera KM-1510... | Answered on Dec 23, 2019

Try this:

Press and hold stop, start, and left exposure key in that order.

Release and press stop again. Use zoom keys to enter 163, press start.

Exit the mode by entering 001 and start, or power off/on.

Kyocera KM-1510... | Answered on Mar 29, 2019

AP = Adding Powder (toner) it's not an error
it's adding toner from the container into the developer unit while displaying AP. when there is enough toner in the container the AP will disappear and copies can be made when there is not enough toner in the container the toner empty light will come on.

Kyocera KM-1510... | Answered on Feb 04, 2019

This is a jam error code check the exit sensor replace if faulty

Kyocera KM-1510... | Answered on Jan 22, 2016

my dear chek LD UNIT

Kyocera KM-1510... | Answered on Jul 08, 2015

clean mirror and ccd camera

Kyocera KM-1510... | Answered on Jul 08, 2015

side door open here fusing unit

Kyocera KM-1510... | Answered on Jul 08, 2015

The Problem:
Polygon motor synchronization problem
The polygon motor does not reach the
stable speed within 15 s of the START
signal turning on


1-Poor contact in the
polygon motor connector
Reinsert the connector. Also check for continuity
within the connector cable. If none,
remedy or replace the cable

2-Defective polygon
Replace the LSU.

3-Defective engine PCB
Replace the engine PCB and check for correct operation.

This wat the service manual say about this error code but as Tech i recommand for you to do this steps before changing any part and this 60% could fix your problem.

First of all open the back of your machine and make sure there is no cable connector is lose, specially those cables that connected to motors, unplug those cables and plug them again, also make sure that the paper fader cable is connected well. after this put the machine on and off and do this steps:

In the operation panel hit 1087 twice, and this will take you to maintenance mode , then select 906 and hit start, look for the words in the screen, hightlight it and hit start again, the machine may be will tell you put the main power off and on, do this and you will be ok.

hope it helps

Kyocera KM-1510... | Answered on Aug 06, 2014

You need to have the developer changed.

Kyocera KM-1510... | Answered on Jun 25, 2014

If its on the rear side of the page would most likely to be the transfer unit. What model is the machine?

Thanks Jason

Kyocera KM-1510... | Answered on Mar 04, 2014

Not finding what you are looking for?
Kyocera KM-1510 Copier Logo

122 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts


Level 3 Expert

85239 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kyocera Office Equipment & Supplies

  • Kyocera Office Equipment & Supplies

Most Popular Question

kyocera mita km km 1635 displays error

  • Office Equipment & Supplies