20 Most Recent Minolta magicolor 3300 Laser Printer Questions & Answers

Log on to Hibana Service Commander program you have with this is very old printer (Sorry) Under life tab you reset the count for the fuser according to the service manual. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

sound like the printer operating system failed nothing to do with drivers get a Konica Minolta tech out to look at it, mite be able to get a firmware from secured web site to re flash the machine. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Replace the image unit try the web site below Precision Roller Printer Toner Cartridges Parts and Supplies Office... Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Recommend you take to a Konica Minolta dealership a latch might be the problem Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

might need a new control board or the firmware could be corrupt. See if you can get a Konicaminolta tech to get the firmware if still available or a new control board or menory Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Check the image unit/drum print out the demo page find which color is printing light and replace that color image unit NOT the TONER Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Your machine mite have been set up under the administrator setting instead of your access. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

What version of Mac OS X are you using? You can find it by choosing "About This Mac" from the Apple menu.

I had the same problem. Check out page 3-308 of this document.
Take off the side cover and re-engage the gear. Should solve the problem.

ftp://ftp.qms.com/pub/cta/out_going/other/diagcd/mc3300sm.pdf

Hello.

Give this a try (from Minolta Support):

1. With the Menu ENGINE selected, press the Down key.
2. Press the PREV key until SERVICE is displayed
3. Press the Select key to display "FACE COUNT".
4. Press both the Select and Down keys at the same time and hold for at least 3 seconds.
5. With Service Person displayed, press the Down key.

You are now in Service Mode

Select "Reset Counter Fuser Unit"

Exit by selecting the Cancel key.

Hope this resolves your problem.

Clean the rollers in the paper path with a moist cloth (NOT WET CLOTH). Keep rolling them and keep cleaning them. Then allow sometime to dry up. Ot if in a hurry then dry them with your hairdryer without the heat.

Its problem with tonner stucked in the outlet window of the cartridge. remove it by hands or buy new cartrigde

try to clean your black cartridge, maybe its dirty. Put it back and try printing.

I had the same problem previously. I had a small piece of paper jam in the imaging unit
pulled it out and got the Imaging Unit Missing error. I could not solve the problem so I called it in under the extended warranty. Even the printer tech could not solve this issue. But, I look at this file, took off a the side cover moved the gear an viola! fixed..

Try page 3-308 of this PDF.

ftp://ftp.qms.com/pub/cta/out_going/other/diagcd/mc3300sm.pdf

iF YOU WANT TO RESET THE TONER COUNTER, YOU MAY NEED A RESET CHIP ON THIS MODEL, SEE:

Reset Chips : Minolta Magicolor 2400w

Take the unit out right away and reseat it again,repeat if nessecary.

For what model sir/mam? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Are all of the image unit and color toner Minolta/QMS (OEM) not third party. Does the machine print the demo page OK? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

What about the machine showing a code or image problem you did not state the problem when you submitted the question. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f